|
|
|
|
About the torsion lowering process |
| • Homepage » PEUGEOT MODELS (FAULTS AND SOLUTIONS) » 206 | |
| 08.05.2020 15:00 | # 1 |
 fahrikem |
|
|
|
|
| 08.05.2020 15:00 | # 2 |
 Guests |
|
|
Ranging from 150 to 250 cleaners
|
|
| 08.05.2020 15:00 | # 3 |
 3rkans |
|
|
So is there any harm in this drop job ??
|
|
| 08.05.2020 15:00 | # 4 |
 boranaydogmus |
|
|
Actually, I am thinking of dropping the back, but first I have to buy a wheel-tire. In Kırşehir, we find the master who will do this job a little difficult. Same setup as Brodway ...
|
|
| 08.05.2020 15:00 | # 5 |
| Guests |
|
|
[QUOTE = boranaydogmus] Actually, I am thinking of dropping the back, but first I have to buy a wheel-tire. In Kırşehir, we find the master who will do this job a little difficult. Same setup as Brodway ... [/ QUOTE] The sounding of the system is very similar to that of the broadway, but it is not the same. broadway is also depreciated. Seen inside the rear fenders. In peugeot and citroen, it works in an amortizing position. it remains almost 50-60 degrees. and there is not much harm in doing this. Sankı vehicle is like ticking in high position. but since the water park will stand more depressed in the depreciation and will work at a shorter distance, maybe a small amount of life can be short. This is a situation that can be ignored. |
|
| 08.05.2020 15:00 | # 6 |
 berko |
|
|
A figure like 150-250 is too high. I did not have 2 years, I changed the bow in front, I dropped the back from torsion, I gave 80 lira.
|
|
| 08.05.2020 15:00 | # 7 |
 ali oncu |
|
|
I think 150 has come a lot to me 100.
|
|
| 08.05.2020 15:00 | # 8 |
 peugeotefe |
|
|
There are those who reduce the torsion to 50 lira
|
|
| 08.05.2020 15:00 | # 9 |
| boranaydogmus |
|
|
My problem here is to find a master who will do more than money. No masters are talking about their knowledge, they say what do we do, like that of the system brodway; but I don't believe what they can do, I'm afraid they'll turn the car into a toy. Now we will find a master in Ankara and get it done. Guys, it has nothing to do with it, but I'll ask you something. I visited the forum a little bit but I couldn't find an explanation about it, sorry if there is any. Can we enter the places where we commented in the forums that we have answered before? Or should we keep in mind the places we entered? I forget the places I wrote and it gets a little difficult to follow. I would be glad if anyone who shares the information. |
|
| 08.05.2020 15:00 | # 10 |
 Carmania |
|
|
I had made the reduction process in Bostancı industry to Pejocu Harun master, and he took 80 TL front and back workmanship.
|
|
| 08.05.2020 15:00 | # 11 |
| Guests |
|
|
[QUOTE = peugeotefe] There are those who reduce the torsion to 50 lira [/ QUOTE] yes 50 lira bt tutuo .. In other words, if the room is the service you go to, you can even get a fee. 50 reasonable but 150 250 rubles !! like a joke
|
|
| 08.05.2020 15:00 | # 12 |
| fahrikem |
|
|
Is there any change of spring etc. in torsion lowering process, is this only lowering process done from torsion gear? The person I bought peugeot 206 has very high torsions.
|
|
| 08.05.2020 15:00 | # 13 |
| peugeotefe |
|
|
There is no spring at the back, the meter calculation is deducted from the torsion shafts.
|
|
| 08.05.2020 15:00 | # 14 |
| xdesign 206 |
|
|
It is very simple we drop the car from torsion in a short time, we cost 40 lira. |
|