508 isofix - 508 - Peugeot Forum

Hello guys,

It has been about 5 months since you joined, but I have encountered a problem and wanted to share it here.

I own the 2012 model 508 petrol, the vehicle is an automatic allure model. Yet at 40,000 km. I am very happy with the vehicle so far and have had no problems. I solved that problem by taking a small bass from himself, as there was a lack of bass in the music system.

The reason I bought the vehicle was that it was a large vehicle and the number of accessories and the price low compared to its equivalents. Six months ago, we now bought a child seat and installed it in the back seat, as a new member joined our family. However, isofix hooks are far above. Therefore, there is a gap of approximately 10 cm between the child seat and the car seat. I can not choose the seats that are fitted with a belt yet, because the baby needs to travel up to 15 months old, and the child seats that are fitted with the belt do not allow this because it does not rotate 360 degrees. As the seat is now 10 cm in the air, it shakes too much as it cannot receive support from the bottom in the pits and bumps due to the space under it. I support this by feeding the gold and putting things like cushions and books, this is not a problem, but God bless, if an accident is higher than the child's height, does not cause larger problems?

I went to the authorized service and consulted the subject, but they stated that isofix was produced in these models and that it was taken where it should be in later models. When I asked for a solution proposal on the subject, they could not help. Did anyone have a similar problem with you?

I used isofix in all vehicles from 207 to 3008, it was not such a problem, but in 3008 I say that the isofix iron is a little higher, so it is difficult for me to put it on and off. If the seat is the same gap when you wear it differently, maybe if your child grows a little bit, if you use the same vehicle, this problem may decrease when the seat changes.

I tried with 3 different seats, the result is always the same, since the hooks are up and all the seats are designed with hooks at the bottom, there is a gap in every brand ...

[QUOTE = iaxuna] I tried with 3 different seats, the result is always the same, since there are hooks above and all the seats are designed with hooks at the bottom, there is a gap in every brand ... [/ QUOTE]

Then there is nothing to do right now, it is a little above me now but the child has reached 15 kg, so we can not play from all over the seat.

Supporting the gold, I shake the shaking, it is not very important.

My carto does not have isofix 2002 model palio Child seat isofixli is also self-arched. I clamped the isofix irons between the seat, and I tightened it tightly with its belt. I wrapped a lap in the car's seat belt. The seat was already heavy, now it does not move, even the strongest place in the car is better quality than the car :). I think the cushion or something under tighten. If your child seat is jagged, it will absorb the impact from the sides.

[QUOTE = iaxuna] Hello guys, ....
I solved that problem by taking a small bass from himself, as the only thing missing was the lack of bass in the music system ..........
[/ QUOTE]

Hello there. I also suffer from the same trouble. The subject I am centering is how do you handle the self-amplified bass electricity? Did you draw a line from the battery? What is your hopper like?

Hello there. I also suffer from the same trouble. The subject I am centering is how do you handle the self-amplified bass electricity? Did you draw a line from the battery? What is your hopper like?
[/ QUOTE]

It is true that we took the electricity directly from the battery with the cable, for the 20-cm box of the loudspeaker, I fixed it in the trunk, it has the advantage of being self-amplified, it has the control to close the sofor seat, you can intervene whenever you want.

Hello, could you describe how you used the isofixe car seat?

My 208 model vehicle

First of all, welcome. I think you should sit down and look at the connection types from the peugeot service box.

We looked at it not universal, but I did not apply power, I thought that maybe there is a tecnique.

Sir, if you have a sales link for the product you have, can you send it?

08.05.2020 20:51	# 2
GokhaN
I used isofix in all vehicles from 207 to 3008, it was not such a problem, but in 3008 I say that the isofix iron is a little higher, so it is difficult for me to put it on and off. If the seat is the same gap when you wear it differently, maybe if your child grows a little bit, if you use the same vehicle, this problem may decrease when the seat changes.

08.05.2020 20:51	# 4
GokhaN
[QUOTE = iaxuna] I tried with 3 different seats, the result is always the same, since there are hooks above and all the seats are designed with hooks at the bottom, there is a gap in every brand ... [/ QUOTE] Then there is nothing to do right now, it is a little above me now but the child has reached 15 kg, so we can not play from all over the seat.

08.05.2020 20:51	# 6
KILIC
My carto does not have isofix 2002 model palio Child seat isofixli is also self-arched. I clamped the isofix irons between the seat, and I tightened it tightly with its belt. I wrapped a lap in the car's seat belt. The seat was already heavy, now it does not move, even the strongest place in the car is better quality than the car :). I think the cushion or something under tighten. If your child seat is jagged, it will absorb the impact from the sides.

08.05.2020 20:51	# 7
pusutr
[QUOTE = iaxuna] Hello guys, .... I solved that problem by taking a small bass from himself, as the only thing missing was the lack of bass in the music system .......... [/ QUOTE] Hello there. I also suffer from the same trouble. The subject I am centering is how do you handle the self-amplified bass electricity? Did you draw a line from the battery? What is your hopper like?

08.05.2020 20:51	# 9
Seustun
Hello, could you describe how you used the isofixe car seat?

	508 isofix
• Homepage » PEUGEOT MODELS (FAULTS AND SOLUTIONS) » 508

08.05.2020 20:51	# 1
iaxuna
Hello guys, It has been about 5 months since you joined, but I have encountered a problem and wanted to share it here. I own the 2012 model 508 petrol, the vehicle is an automatic allure model. Yet at 40,000 km. I am very happy with the vehicle so far and have had no problems. I solved that problem by taking a small bass from himself, as there was a lack of bass in the music system. The reason I bought the vehicle was that it was a large vehicle and the number of accessories and the price low compared to its equivalents. Six months ago, we now bought a child seat and installed it in the back seat, as a new member joined our family. However, isofix hooks are far above. Therefore, there is a gap of approximately 10 cm between the child seat and the car seat. I can not choose the seats that are fitted with a belt yet, because the baby needs to travel up to 15 months old, and the child seats that are fitted with the belt do not allow this because it does not rotate 360 degrees. As the seat is now 10 cm in the air, it shakes too much as it cannot receive support from the bottom in the pits and bumps due to the space under it. I support this by feeding the gold and putting things like cushions and books, this is not a problem, but God bless, if an accident is higher than the child's height, does not cause larger problems? I went to the authorized service and consulted the subject, but they stated that isofix was produced in these models and that it was taken where it should be in later models. When I asked for a solution proposal on the subject, they could not help. Did anyone have a similar problem with you?

08.05.2020 20:51	# 11
sonerkyl
First of all, welcome. I think you should sit down and look at the connection types from the peugeot service box.

08.05.2020 20:51	# 12
Seustun
We looked at it not universal, but I did not apply power, I thought that maybe there is a tecnique.

08.05.2020 20:51	# 13
sonerkyl
Sir, if you have a sales link for the product you have, can you send it?