Peugeot Forums - Peugeot Fan Club

407 Door speaker replacement

Homepage » PEUGEOT MODELS (FAULTS AND SOLUTIONS) » 407
08.05.2020 20:49 # 1
necmettinn
Hello again to everyone ... I have previously opened a topic about the rear view camera installation. Our efforts to beautify my vehicle still continue. I haven't opened a new topic for the little things I did in the meantime, but since I thought that the speaker replacement is something that may be necessary for everyone, I found it appropriate to open it. Hopefully it will work for someone ... First of all, let me state this is a simple operation that anyone who can hold a screwdriver can do. Since the new speaker depth and magnet dimensions are the same as the original speaker, there was no problem. In a video I watched on the internet, he said that for the speaker replacement, the speaker is screwed and is a plastic piece attached to the door with a rivet, and because the depth is not enough, the bottom should be cut and a new speaker magnet should be made available. I did not need this process because the dimensions fit ... Let's start the process immediately ..... There are screws and door clips at the points I marked in the picture. I removed the screws and carefully removed the part with the glass opening button (there is no screw in this section, the purpose is just to remove the socket of the button). As I was removing the glass opening button, I started to save the nails from the side where the button was, as there was a 3 cm piece that entered the lath on the side of the door handle. There were plastic attachments that I bought before to remove the door clips. Then I removed the door trim upward. The point to be noted here is that there is a long piece of butterfly on the glass side at the top of the door trim. It is attached towards the bottom direction of the door. I tried replacing the new speaker after removing them, since I saw that there was no problem, there was no need to remove the lower plastic parts. I cut the connectors from the socket and connected the cable of the new speaker to the old speaker cable and taped it nicely.Veee installed our new speaker in place and tested its sound ... There is a part inside the glass edge rubber on the upper part of the floor, it is easier if we attach it carefully by paying attention during the installation phase .... The disassembly of the left door is the same way ... As seen in the pictures, instead of the screws on the door handle, only the screw holds the glass module. No need to dismantle the area where the door opening lever is located. First, after removing the screws and then removing the door clips, I changed the speaker in the same way. Just one more screw under the door handle on the top of the door pocket, that's the only difference. I hope to change the rear door speakers in the future, I will share their photos and stages under this heading. .A pleasant accident-free ride for everyone ... good night ...
08.05.2020 20:49 # 2
necmettinn
.........CORRECTION........
I wrote that when removing the left door trim, it is not necessary to remove the inner door opening lever frame. But since I removed this frame myself, I may not have had a problem removing the door trim. I think it would be useful to disassemble the floor in case it can hold ...
08.05.2020 20:49 # 3
M.Ahmet059
I wonder what brand of speakers did you wear? What are the wattage values? Does it sound better? (compared to the speaker before it was broken :))

Also, the screws holding the speakers fit the rivet holes very well. The back plate was riveted.
08.05.2020 20:49 # 4
sonerkyl
The teacher gives thanks to their health and detailed explanation.
08.05.2020 20:49 # 5
GokhaN
I have been doing a successful work
08.05.2020 20:49 # 6
necmettinn
[QUOTE = M.Ahmet059] I wonder what brand of speakers did you install? What are the wattage values? Does it sound better? (compared to the speaker before it was broken :))

Also, the screws holding the speakers fit the rivet holes very well. The back plate was riveted.
[/ QUOTE]

Speakers skytech SKT-2400 is a 500watt dual twitter speaker. According to what I have researched on the internet, it is an attractive product as a price that does not match the pionner quality. Since the bellows tires of the old speakers are torn, even if you bring the volume to 12 level, it was bothering and sizzling. At least that problem was gone. Of course, it can't be like amplifiers in terms of performance, but I was expecting a better sound, but it still works for now.
The screws holding the speakers hold the plastic hitch and the original. The rivets hold the plastic part of the speaker to the door sheet, and I have never touched them. Of course, you can use clip-on speaker screws instead of rivets. Have a nice day...
08.05.2020 20:49 # 7
necmettinn
I hope I will continue to share what I did. Good luck with...
08.05.2020 20:49 # 8
Crayzmetin
Teacher, health has been a very good work. An application I will do soon. It will help a lot. Thanks
08.05.2020 20:49 # 9
necmettinn
[QUOTE = Crayzmetin] Teacher, health has been a very good work. An application I will do soon. It will help a lot. Thanks [/ QUOTE]

How happy it would help me ... easy come ...
A limited number of service data is available through membership at http://public.servicebox.peugeot.com/pages/index.jsp. Details of nail and screw locations of the front and rear doors are already in the pictures, but the original is as follows ....



08.05.2020 20:49 # 10
LUDACRIS
a very detailed and pleasant sharing of health
08.05.2020 20:49 # 11
necmettinn
[QUOTE = LUDACRIS] a very detailed and pleasant sharing of health to your hand [/ QUOTE] Thank you :)
01.11.2021 00:05 # 12
zencefil
Thanks it was very helpful.
Peugeot Forums - Peugeot Fan Club © 2025
“The most auspicious of people, it is people who are useful.”