308 STOP AND NO WORKING AFTER THE FIRST START - 308 (2008-2013)

Hello Dear Forum Members,

First of all, I just joined you and I will be asking you for your ideas about the problem I am having.

My vehicle is 2010 model 308 1.6Hdi 109hp automatic (81000 km) and I live in Izmir. Recently, it stops from time to time, approximately 5 seconds after starting my vehicle for the first time in the morning, and then works at the start pressure for the 8th and 9th times.

When I examined the situation for detection; If the nose of the vehicle has waited for approximately 1 hour in the air, it causes the problem of stopping and not working continuously. If the car's nose is down, it does not cause any problems. Although the vehicle is flat, it does not usually cause problems, but I am encountering this problem from time to time (once or twice a week).

Regarding the problem, the services have changed the diesel filter, the tank float and the diesel hose parts called the puller, but none of them has been solved.

Instead of constantly changing parts by trial and error, I wanted to ask you, the valuable forum members, on the subject. I kindly request your valuable guidance regarding the solution of the problem.

Injectors should be checked. Probably at least one of the injector washers is worn and it gets air from there. This causes the fuel to escape back.

By the way, I hope the parts you replace are the original parts.

now it will be ridiculous, but I will suggest you replace the diesel filter with an original filter.

the same problem happened to me, my brother passed by, he was working, the car was stationing after 5 seconds.

If he does not work now, if he gives the same error until the pump goes, open the hood, then start the gas by wiping the gas until the hand pump is picked up and then the gas is fired.

Thank you for your valuable comments, dear friends. Considering what you said about the subject, I think it is necessary to focus on making the air first and then on the injectors.

@ Aykut28: When I tighten the hand pump until it hardens, it works at the third time instead of the 8th or 9th time.

It should not be at 3. In fact, until it hardens 5 times 10 times later, gas wastes, make mars for 4 seconds.

Friends, I have the same problem. When I connect the ELM327 to the device, P0093 malfunctioned, usually the car stops a minute after the first operation in the mornings. Is there a master that you can recommend? It is a chance to come across a good master. I have not come across until now.

Hello Again Forum Members,

My problem was solved only by a detailed and devoted work by a third special service that I went to. I express my gratitude to Emrah Candan Usta, who is working in Izmir Çiğli Ata Industry, who has put great effort in determining where the malfunction is caused and resolved at a very cheap cost and who gives confidence to the customers to behave very warmly.
As a result; It was determined that the fault originated from fuel hoses coming from the tank to the engine side and a check valve was added to the hoses in order not to increase the cost. Until this stage, many different services were replaced by parts such as tank float - hoses with grips - diesel sensor - fuel filter. We once again understood the importance of the right master.

@cc than

Hello Mr. Candan,

As a person who has been dealing with the same problem for about 2 months and spending a lot of money in different services; I can recommend the Cömert Automotive-Emrah Master located directly in İzmir Çiğli Ata Sanayi. In order not to increase the cost, he worked on the vehicle for 10 days without ordering new parts, and after performing the exact determination, he went to the part replacement & repair and received only a symbolic fee.

08.05.2020 20:57	# 1
aniloz
Hello Dear Forum Members, First of all, I just joined you and I will be asking you for your ideas about the problem I am having. My vehicle is 2010 model 308 1.6Hdi 109hp automatic (81000 km) and I live in Izmir. Recently, it stops from time to time, approximately 5 seconds after starting my vehicle for the first time in the morning, and then works at the start pressure for the 8th and 9th times. When I examined the situation for detection; If the nose of the vehicle has waited for approximately 1 hour in the air, it causes the problem of stopping and not working continuously. If the car's nose is down, it does not cause any problems. Although the vehicle is flat, it does not usually cause problems, but I am encountering this problem from time to time (once or twice a week). Regarding the problem, the services have changed the diesel filter, the tank float and the diesel hose parts called the puller, but none of them has been solved. Instead of constantly changing parts by trial and error, I wanted to ask you, the valuable forum members, on the subject. I kindly request your valuable guidance regarding the solution of the problem.

08.05.2020 20:57	# 2
pusutr
Injectors should be checked. Probably at least one of the injector washers is worn and it gets air from there. This causes the fuel to escape back. By the way, I hope the parts you replace are the original parts.

08.05.2020 20:57	# 4
Aykut 28
the same problem happened to me, my brother passed by, he was working, the car was stationing after 5 seconds.

08.05.2020 20:57	# 5
Aykut 28
If he does not work now, if he gives the same error until the pump goes, open the hood, then start the gas by wiping the gas until the hand pump is picked up and then the gas is fired.

08.05.2020 20:57	# 6
aniloz
Thank you for your valuable comments, dear friends. Considering what you said about the subject, I think it is necessary to focus on making the air first and then on the injectors. @ Aykut28: When I tighten the hand pump until it hardens, it works at the third time instead of the 8th or 9th time.

	308 STOP AND NO WORKING AFTER THE FIRST START
• Homepage » PEUGEOT MODELS (FAULTS AND SOLUTIONS) » 308 (2008-2013)

08.05.2020 20:57	# 3
GokhaN
now it will be ridiculous, but I will suggest you replace the diesel filter with an original filter.

08.05.2020 20:57	# 8
ccandan
Friends, I have the same problem. When I connect the ELM327 to the device, P0093 malfunctioned, usually the car stops a minute after the first operation in the mornings. Is there a master that you can recommend? It is a chance to come across a good master. I have not come across until now.

08.05.2020 20:57	# 10
aniloz
@cc than Hello Mr. Candan, As a person who has been dealing with the same problem for about 2 months and spending a lot of money in different services; I can recommend the Cömert Automotive-Emrah Master located directly in İzmir Çiğli Ata Sanayi. In order not to increase the cost, he worked on the vehicle for 10 days without ordering new parts, and after performing the exact determination, he went to the part replacement & repair and received only a symbolic fee.