307 XR 2003 Airbag Light Resistance Connection - 307

Friends, my 307 xr vehicle gives airbag error. The airbags and under the steering wheel have been checked, no problem. A resistance connection had to be made. How many ohms resistor must be installed. I expect help from friends who have knowledge. Thanks good forums ....

It will be 2.2ohm. it is useless when it is different even if it is very close to this value. the exact value is 2.2 ohms.

Thanks tomorrow I'm trying the first job. This Resistance connection creates problems in opening the airbag in case of an accident.

I just tried 2.2ohm, 1.7ohm, 22ohm the problem persists. Where else can I have the problem? I tried the resistance connections in the sockets under the front seats. I have tried several resistors of the same value from 2.2 ohm resistors

Well, the airbag is used in vehicles that open the airbag. Is your airbag hungry to show the airbag as if it was there?

something different but I wanted to write;

The airbag light is on me too ... Airbaler on the side pillars and seats are showing off ... I went to the auto clinic, we will resist as if we were resisting, we will erase the malfunction in the brain once the brain has received the malfunction. When he said how much the fee is, he said 150 TL ... Is it normal?

yes, if normal eruption this is done

[QUOTE = muro_60] is good for vehicles that open airbags. Is your airbag hungry to show as if there is an airbag? [/ QUOTE]
No, the airbag has been checked, it is not clear. The films inside the steering wheel have also been checked. No problem.

[QUOTE = db_61] [QUOTE = muro_60] is well used in vehicles that open airbags Are you hungry to show as if there are airbags? [/ QUOTE]
No, the airbag has been checked, it is not clear. The films inside the steering wheel have also been checked. No problem.
[/ QUOTE] then you have to look for the fault in your brain if drec is attached they will not hurt at the time of the accident.

Thank you connected to the computer, the problem appeared in the winding under the steering wheel. The winding is checked, there is no problem in the winding.

The socket of the airbag in the steering wheel looks very precise, but it does not sit. I had it burned.

okay teacher check it again thanks

Hello friends,

The subject is old, but I am saying another place to give an idea.

There is one more resistor cable connection by the trunk when you open the ceiling tile. As the known backs are torsion, they can sometimes play shaking and get damaged. Be sure to check the resistors there. After investigating my airbag light so much, the light went out when he realized that he was making the resistance there.

Also, a footnote: We all know that it can burn from the winding on the steering wheel. I still have this problem. With the steering wheel up-down and depth adjustments, I moved it to a non-flammable position. My seamless position, the steering is at the bottom and closest to me.

Your information...

[QUOTE = EmRRmE] Hello Friends,

The subject is old, but I am saying another place to give an idea.

Your information...

[/ QUOTE]

As a +, let me add that the air light of the airbeam was on me whenever I bought it, they said com2000 will change or airbag winding will be repaired. When I was reading the subject of a friend in our form, I saw what he had removed the cover under the steering wheel, the airbag socket was loosened when it snapped in place, it was fixed, and I said, let me get down to my car, and I put the same problem socket in place, and the airbag lamp went off.

08.05.2020 18:56	# 2
syavuz
It will be 2.2ohm. it is useless when it is different even if it is very close to this value. the exact value is 2.2 ohms.

08.05.2020 18:56	# 6
10ur28
something different but I wanted to write; The airbag light is on me too ... Airbaler on the side pillars and seats are showing off ... I went to the auto clinic, we will resist as if we were resisting, we will erase the malfunction in the brain once the brain has received the malfunction. When he said how much the fee is, he said 150 TL ... Is it normal?

08.05.2020 18:56	# 14
sonerkyl
[QUOTE = EmRRmE] Hello Friends, The subject is old, but I am saying another place to give an idea. There is one more resistor cable connection by the trunk when you open the ceiling tile. As the known backs are torsion, they can sometimes play shaking and get damaged. Be sure to check the resistors there. After investigating my airbag light so much, the light went out when he realized that he was making the resistance there. Also, a footnote: We all know that it can burn from the winding on the steering wheel. I still have this problem. With the steering wheel up-down and depth adjustments, I moved it to a non-flammable position. My seamless position, the steering is at the bottom and closest to me. Your information... [/ QUOTE] As a +, let me add that the air light of the airbeam was on me whenever I bought it, they said com2000 will change or airbag winding will be repaired. When I was reading the subject of a friend in our form, I saw what he had removed the cover under the steering wheel, the airbag socket was loosened when it snapped in place, it was fixed, and I said, let me get down to my car, and I put the same problem socket in place, and the airbag lamp went off.

	307 XR 2003 Airbag Light Resistance Connection
• Homepage » PEUGEOT MODELS (FAULTS AND SOLUTIONS) » 307

08.05.2020 18:56	# 1
db_61
Friends, my 307 xr vehicle gives airbag error. The airbags and under the steering wheel have been checked, no problem. A resistance connection had to be made. How many ohms resistor must be installed. I expect help from friends who have knowledge. Thanks good forums ....

08.05.2020 18:56	# 5
muro_60
Well, the airbag is used in vehicles that open the airbag. Is your airbag hungry to show the airbag as if it was there?

08.05.2020 18:56	# 10
db_61
Thank you connected to the computer, the problem appeared in the winding under the steering wheel. The winding is checked, there is no problem in the winding.

08.05.2020 18:56	# 11
muro_60
The socket of the airbag in the steering wheel looks very precise, but it does not sit. I had it burned.

08.05.2020 18:56	# 13
EmRRmE
Hello friends, The subject is old, but I am saying another place to give an idea. There is one more resistor cable connection by the trunk when you open the ceiling tile. As the known backs are torsion, they can sometimes play shaking and get damaged. Be sure to check the resistors there. After investigating my airbag light so much, the light went out when he realized that he was making the resistance there. Also, a footnote: We all know that it can burn from the winding on the steering wheel. I still have this problem. With the steering wheel up-down and depth adjustments, I moved it to a non-flammable position. My seamless position, the steering is at the bottom and closest to me. Your information...