307 Removing the Rear Bumper and Removing Water Leaks .. - 307

Hi friends, I was at home today, I said I'll take care of my car. When it comes to the subject, I said, "I will take it to the body shop, I did not deal with it."

First let me tell you what I did I couldn't find enough explanation on the site to remove the bumper.

1. There is a screw holding the base of the rear drums, a nut and 3 clips around.

2. There are full star screws holding the corners of the bumper by stretching the bases of the drums.

3. We open our backlights, open the rear floors and open the places fastened with two nuts with 13 open mouth wrenches and pull the stops. There is a smart screw that holds the bumper under the stops and there is a clip. We unscrew the screw with the 13 open-mouth wrench.

4. After finishing, we remove the bumper by gently pulling the bumper on the sides where we do the last disassembly. you can disassemble the license plate lamps completely.

5. There is a plastic bakelite all along, we need to remove them, there are 6-7 nuts.

6. As seen in the pictures, we prevent the water from leaking by pulling black silicon around the air vents in the bumper.

7. We collect the buffer by reversing the operations. After 1.5 hours of work, the process is complete. Because there is no place to take another water, wishing it will not get any more water.

Dismantled

Left Vent siliconised.

Right Vent siliconised.

This is siliconized from below.

This is the middle sponge seal that is likely to get water under the aeration I mentioned.

Peugeot35 2017-02-08 20:56:56

I hope your health teacher will not take water again.

The subject has been moved.

sonerkyl 2016-12-12 09:25:03

health to your hand

I closed those gaps directly, radical solution :)

Another detail is the taillights. There is a sponge-like material behind the stops. I put it in front of the stop and squeezed it to the number ten.

[QUOTE = fætih] another detail is taillights. There is a sponge-like material behind the stops, I put it in front of the stop, I squeezed it into the number ten, the water does not enter. [/ QUOTE]

Yes, my stop sponges were intact so I did not take action.

If anyone thinks that water has entered the saddle stop, there is dust behind the stop and it becomes obvious that water has entered from there.

I just got a trace of water in the ventilation slot.

My work, which has not been affected by heavy rain in İzmir for 2/3 days, has been successful.

RESULT POSITIVE!

If the luggage spare wheel place becomes an aquarium after the rain, especially if the fish can swim :) they can get positive results by trying this process. Your information..

DELETED PICTURES HAVE BEEN UPDATED .. Peugeot35 2017-02-08 21:00:21

Hello, would you like to add the pictures again. The worst feature of the forum is that the following pictures are not in their own servant, so almost all topics cannot reach their purpose.

08.05.2020 20:04	# 8
01MRT
Hello, would you like to add the pictures again. The worst feature of the forum is that the following pictures are not in their own servant, so almost all topics cannot reach their purpose.

	307 Removing the Rear Bumper and Removing Water Leaks ..
• Homepage » PEUGEOT MODIFIED PLATFORM » 307

08.05.2020 20:04	# 1
Peugeot35
Hi friends, I was at home today, I said I'll take care of my car. When it comes to the subject, I said, "I will take it to the body shop, I did not deal with it." First let me tell you what I did I couldn't find enough explanation on the site to remove the bumper. 1. There is a screw holding the base of the rear drums, a nut and 3 clips around. 2. There are full star screws holding the corners of the bumper by stretching the bases of the drums. 3. We open our backlights, open the rear floors and open the places fastened with two nuts with 13 open mouth wrenches and pull the stops. There is a smart screw that holds the bumper under the stops and there is a clip. We unscrew the screw with the 13 open-mouth wrench. 4. After finishing, we remove the bumper by gently pulling the bumper on the sides where we do the last disassembly. you can disassemble the license plate lamps completely. 5. There is a plastic bakelite all along, we need to remove them, there are 6-7 nuts. 6. As seen in the pictures, we prevent the water from leaking by pulling black silicon around the air vents in the bumper. 7. We collect the buffer by reversing the operations. After 1.5 hours of work, the process is complete. Because there is no place to take another water, wishing it will not get any more water. Dismantled Left Vent siliconised. Right Vent siliconised. This is siliconized from below. This is the middle sponge seal that is likely to get water under the aeration I mentioned. Peugeot35 2017-02-08 20:56:56

08.05.2020 20:04	# 2
sonerkyl
I hope your health teacher will not take water again. The subject has been moved. sonerkyl 2016-12-12 09:25:03

08.05.2020 20:04	# 3
pepecura
health to your hand I closed those gaps directly, radical solution :)

08.05.2020 20:04	# 4
fætih
Another detail is the taillights. There is a sponge-like material behind the stops. I put it in front of the stop and squeezed it to the number ten.