307 HDI Buffer removal - 307

Hello friends . Are there any friends who will tell us about the 307 hdi bumper removal and installation work ...

I need it better me :))

If it works for you, I can tell you in writing: D Text can also help, and it has been inserted. Koliva 2011-08-23 10:26:50

If it is illustrated, it would be more ii .. tell you. I am sure it will be beneficial for him .. tsk.

my teacher. My grille under the grill dipped the paint, I will paint it off

[QUOTE = heffera] slm friends. Do you have any friends who will tell us about the 307 hdi bumper removal and installation work ... [/ QUOTE]

The model of your vehicle is certain, but the model year is not certain.

You should share your province and district information in your profile information.

Another request is that you should specify the model year of your vehicle in the signature section, because there are two different models and the bumpers are different. If you share the engine model, fuel type, equipment etc. while specifying the ready model year, you will not have to answer the questions about the vehicle in your next problem.

[QUOTE = text]

The model of your vehicle is certain, but the model year is not certain.

You should share your province and district information in your profile information.

[/ QUOTE]

This is valid for 2003 model 307. As Metin said, there may be differences in other models. I copy exactly from my old articles:

In fact, it was not easy, but it does not need much in a second person. If you want me to write the steps, maybe you will need it or someone else.

1. There is a 10mm screw in the hoods of ten wheels. First we remove them.
2. We lie under the car and remove the clips on the lower ends. 2 on the right, 2 on the left. There are also 2 screws in the place below the plate. It is already easily seen. We put them in.
3. There are 4 plastic clips on the sides of where the bonnet release latch is located. We insert them and 2 ser screws on the right side, and insertion is ok.
4. The most crucial point of the business is here. We grasp the screw that we put in the hood and gently hang it. Just below the screw and from the line on its side, the buffer has metal wearing places. Asily when he saves from these places, he emerges as a sip and goes to the other end.

That's all.

Koliva 2011-08-23 10:45:40

What I am wondering is whether you need to remove the bumper to remove the headlights.

[QUOTE = eye] I was wondering if you need to remove the headlights in the bumper to remove the headlights. Anybody know who you are. [/ QUOTE]

Yes there is need Gülme

It was the 2nd series of 2005 model ... I learned this when changing the disk. There are two types of the 2005 series .. :) I could not find the industry disc.

the rear bumper? if you tell him too ...

[QUOTE = heffera] 2005 was the 2nd series ... I learned this when the disk was changed. There are two types of the 2005 series .. :) I could not find the industry disc.

the rear bumper? if you tell him too ...

[/ QUOTE]

When it came to the 2nd series, new safes came out at the end of 2005

Type 1 old case 307

buddha new safe 307

[QUOTE = Koliva]
[QUOTE = eye] I was wondering if you need to remove the headlights in the bumper to remove the headlights. Anybody know who you are. [/ QUOTE]

Yes there is need Gülme

[/ QUOTE]

Well, I'm demolished now,
I was thinking about opening and painting the headlight: S

slm. text brothers, the red one .. I said, the next industry was changing the disc. There was no one coming out of the car ... the magnet was different. it comes together with the ball. 40 tl or something was not done .. we had to plug the original .. particle your car 2005 in 2 series said ??

Disc and ball separate in 1 series

In 2 series, it was fitted with a disc and ball ..

a Hefferman 2011-08-23 11:09:22

the old case is easy to remove the bumper, it is easier to put on, just as the coach said.

I can't help you because your vehicle is the new safe (:

[QUOTE = koliva] [QUOTE = eye] I am wondering, is it necessary to remove the bumper to remove the headlamps. Anybody who knows. [/ QUOTE]

Yes there is need Gülme

[/ QUOTE]

yes there is a need. Be careful, do not take the hood out. Otherwise, only one of the nine masters like me can not sit on the hood and you can see that the hood of the hood will be on your side as you go fast. Nuke

I think we will remove the dowels of the hood and leave it where it is.

Yeah exactly like that.

[QUOTE = my eye] I think we will remove the dowels of the hood and leave it where it is. [/ QUOTE]

You will only remove the dowels on the bumper side of the hood, there is no need for others,

updated .... rear bumper removal ?? on the right there is a 1, 2 cm slump ... I'm going to pull it ... the man said 100 TL to disassemble. let me do it myself ... it shouldn't be too hard.

puller (2 cm dent correction): 100 tl

removal, installation: 100 TL

buffer (sub-industry): 200 TL

painting: 100 tl

Anybody who knew what it is now 1 year ago.

I am thinking of having a parking sensor ... I guess it would be 100 TL ...

[QUOTE = heffera] updated .... rear bumper removal ?? on the right there is a 1, 2 cm slump ... I'm going to pull it ... the man said 100 TL to disassemble. let me do it myself ... it shouldn't be too hard.