307 Glass Water Tank problem! RESOLVED .... - 307

Glass is pouring water from the throat of the long pipe we poured water!

Let me go into detail, when the tank fills up, when it fills the tank pipe to the brim, the water is missing from the throat that joins thinly. I dismantled the pipe was quite dirty, I washed it beautifully, I cleaned it, the gasket was intact, I washed it again, I put it back again, the tank is filling, no problem. I left it as usual.

Is it right to fill the pipe until the water level is full or is it correct?

Peugeot35 2017-08-21 19:59:41

I think there is no need to fill the pipe. If you know the amount you use in the tank, there is no need to fill it completely, it does not weigh

[QUOTE = tsufrankwoli] I don't need to fill the pipe. If you know the amount you use in the tank, there is no need to fill it completely, it does not weigh

[/ QUOTE]

My guess is that the water is leaking and leaking! I guess what I did was to fill that pipe tank.

If you fill the pipe to the brim, it discards the excess water. I thought it was a hole in the warehouse. He evacuates a certain level.

In my opinion, in this regard, the pipe is used to fill the water into the tank below.

I fill it until the pipe is full. There is no such thing as overflowing or draining the water.

I think you can not put on the gasket of the throat first to the tank and then the throat.

[QUOTE = 307 1.4 hdi] I fill the pipe until it is full. Nothing like overflowing or draining the water. [/ QUOTE]

I fill the pipe. When I use the glass water, it starts to drip slowly. You will see if you follow the thinner decreases over time.

[QUOTE = ismailkaya] you can't wear well i guess put the gasket of your neck first in the tank then the throat [/ QUOTE]

I wear it, but two days later, when he uses his glass water, he gets too thin, so he misses it, but when the water in the pipe is low, he does not.

[QUOTE = Peugeot35] [QUOTE = 307 1.4 hdi] I fill the pipe until it is full. Nothing like overflowing or draining the water. [/ QUOTE]

I fill the pipe. When I use the glass water, it starts to drip slowly. You will see if you follow the thinner decreases over time.

[/ QUOTE]

I did what you said and removed the bumper and examined it, but I do not even have the slightest dropping, hodja.

[QUOTE = 307 1.4 hdi] [QUOTE = Peugeot35] [QUOTE = 307 1.4 hdi] I fill the pipe until it is full, nothing like overflowing or draining the water. [/ QUOTE]

I fill the pipe. When I use the glass water, it starts to drip slowly. You will see if you follow the thinner decreases over time.

[/ QUOTE]

I did what you said and removed the bumper and examined it, but I do not even have the slightest dropping, hodja.

[/ QUOTE]

It is true, but my teacher is that I use glass water without inserting the water pipe. It does not drip. As if the water is overpowering, carrying the water in the tank, I could not understand at all :) I also use antifreeze glass water.

By opening the front clips of the right drum without removing the bumper, you could reach the glass water tank if you hurted slightly. your workmanship has been troublesome.

I had this problem when I first bought it. I cleaned it and put it on again and missed it again .. But it hasn't missed for the last 2 years.

I don't know when I put the water in the tank, but you didn't know 1, it's been 2 months. I recently ran the wiper water. There was a stench around him. as if someone fled. water got on my hand and washed 3 times that smell didn't go away what causes this smell? It has never happened to me.

[QUOTE = ggitaristt] I had this problem when I first got it. I cleaned it and put it on again and missed it again .. But it hasn't missed for the last 2 years.
[/ QUOTE]

exactly, my teacher is not a problem, it draws my attention to the pipe when it fills up, if it does not leak, then what happens is that it does not discard the water when there is less water in the pipe, as I said, I will either use it twice a month or not.

[QUOTE = x571] I don't know when I put the water into the tank, but you did not know 1 has been 2 months. I recently ran the wiper water. There was a stench around him. as if someone fled. water got on my hand and washed 3 times that smell didn't go away what causes this smell? It has never happened to me. [/ QUOTE]

LOL

[QUOTE = Peugeot35] Glass water is leaking water from the throat of the long pipe we poured!

Is it right to fill the pipe until the water level is full or is it correct?

[/ QUOTE]

SOLUTION......

There was blue glass water under the car again in the morning, so a lot of water had flowed, and my nerves broke and I immediately got to work.

As I said, when looking for the problem from the place where the tank pipe meets, the glass water tank can be accessed very easily without even removing the buffer and you can even change the tank.

I removed the clips and screws of the drum on the side of the tank, I detected the first problem, I was missing the gasket of the water engine, I removed the engine, the gasket was intact, I wrapped the gasket on the gasket, then I installed the engine, the problem was solved .......... when I said, water flowed from another place as seen in the pictures. a curved sheet in the bumper was pressed to the side of the tank and pierced the tank! (I couldn't understand what that sheet was)

I took the drilled place to the plastic welder, he said he wouldn't hold it even if there was no welding, I brought it home, I put plastic glue on the drilled place, poured plastic adhesive bali on top of it, it was like a bone.

Thank you to all the friends who wrote their opinions on the subject.

I DON'T TAKE THE PICTURES WORKING WITH ONE HAND IS VERY DIFFICULT I HAVE SURVENED UNDER THE CAR.

IT IS ONE OF THE SUBSEQUENT SEAL PROBLEMS AS SEEN. I WASHED THE TANK AT THE SAME TIME. IT WAS RELEASED IN THE BRIGHTENER.

DRILLED PLACE

BUDA REPAIRED

BUDDING ENGINE CHANGE IS VERY EASY AND SIMPLE.

I read the subject to the last letter.

It was an interesting but very interesting subject.

I would like to thank everyone who showed interest and shared their ideas for the effort, sharing the pictures, comments. Clap

[QUOTE = ALLEX] I read the subject to the last letter.

It was an interesting but very interesting subject.

I would like to thank everyone who showed interest and shared their ideas for the effort, sharing the pictures, comments. Clap

[/ QUOTE]

Thanks to our friends, we are trying to solve it when we don't have to. :) the result will hopefully help friends who have this problem.

[QUOTE = Peugeot35] [QUOTE = 307 1.4 hdi] [QUOTE = Peugeot35] [QUOTE = 307 1.4 hdi] I fill the pipe until it is full. There is nothing like overflow or draining the water. [/ QUOTE]

I fill the pipe. When I use the glass water, it starts to drip slowly. You will see if you follow the thinner decreases over time.

[/ QUOTE]

I did what you said and removed the bumper and examined it, but I do not even have the slightest dropping, hodja.

[/ QUOTE]

By opening the front clips of the right drum without removing the bumper, you could reach the glass water tank if you hurted slightly. your workmanship has been troublesome.

[/ QUOTE]

The reason for disassembling the bumper is that I pulled the fog lamp installation and adjusted the places, I said let me look at it when it was ready to disassemble it, but what came to my strange came to me when the color of your water tank was black, not transparent plastic. Smile

Glad you did the dropping problem. Smile

It really felt strange to puncture that tank. If you go to the health industry with your hands, no master will change unless you are very friendly. It cost you free. Clap

08.05.2020 20:31	# 4
talip206
If you fill the pipe to the brim, it discards the excess water. I thought it was a hole in the warehouse. He evacuates a certain level.

08.05.2020 20:31	# 6
Orcun.Dmr
I fill it until the pipe is full. There is no such thing as overflowing or draining the water.

08.05.2020 20:31	# 10
Orcun.Dmr
[QUOTE = Peugeot35] [QUOTE = 307 1.4 hdi] I fill the pipe until it is full. Nothing like overflowing or draining the water. [/ QUOTE] I fill the pipe. When I use the glass water, it starts to drip slowly. You will see if you follow the thinner decreases over time. [/ QUOTE] I did what you said and removed the bumper and examined it, but I do not even have the slightest dropping, hodja.

08.05.2020 20:31	# 16
Peugeot35
[QUOTE = Peugeot35] Glass water is leaking water from the throat of the long pipe we poured! Let me go into detail, when the tank fills up, when it fills the tank pipe to the brim, the water is missing from the throat that joins thinly. I dismantled the pipe was quite dirty, I washed it beautifully, I cleaned it, the gasket was intact, I washed it again, I put it back again, the tank is filling, no problem. I left it as usual. Is it right to fill the pipe until the water level is full or is it correct? [/ QUOTE] SOLUTION...... There was blue glass water under the car again in the morning, so a lot of water had flowed, and my nerves broke and I immediately got to work. As I said, when looking for the problem from the place where the tank pipe meets, the glass water tank can be accessed very easily without even removing the buffer and you can even change the tank. I removed the clips and screws of the drum on the side of the tank, I detected the first problem, I was missing the gasket of the water engine, I removed the engine, the gasket was intact, I wrapped the gasket on the gasket, then I installed the engine, the problem was solved .......... when I said, water flowed from another place as seen in the pictures. a curved sheet in the bumper was pressed to the side of the tank and pierced the tank! (I couldn't understand what that sheet was) I took the drilled place to the plastic welder, he said he wouldn't hold it even if there was no welding, I brought it home, I put plastic glue on the drilled place, poured plastic adhesive bali on top of it, it was like a bone. Thank you to all the friends who wrote their opinions on the subject. I DON'T TAKE THE PICTURES WORKING WITH ONE HAND IS VERY DIFFICULT I HAVE SURVENED UNDER THE CAR. IT IS ONE OF THE SUBSEQUENT SEAL PROBLEMS AS SEEN. I WASHED THE TANK AT THE SAME TIME. IT WAS RELEASED IN THE BRIGHTENER. DRILLED PLACE BUDA REPAIRED BUDDING ENGINE CHANGE IS VERY EASY AND SIMPLE.

08.05.2020 20:31	# 18
Peugeot35
[QUOTE = ALLEX] I read the subject to the last letter. It was an interesting but very interesting subject. I would like to thank everyone who showed interest and shared their ideas for the effort, sharing the pictures, comments. [/ QUOTE] Thanks to our friends, we are trying to solve it when we don't have to. :) the result will hopefully help friends who have this problem.

	307 Glass Water Tank problem! RESOLVED ....
• Homepage » PEUGEOT MODELS (FAULTS AND SOLUTIONS) » 307

08.05.2020 20:31	# 2
tsufrankwoli
I think there is no need to fill the pipe. If you know the amount you use in the tank, there is no need to fill it completely, it does not weigh

08.05.2020 20:31	# 7
ismailkaya
I think you can not put on the gasket of the throat first to the tank and then the throat.

08.05.2020 20:31	# 11
Peugeot35
[QUOTE = 307 1.4 hdi] [QUOTE = Peugeot35] [QUOTE = 307 1.4 hdi] I fill the pipe until it is full, nothing like overflowing or draining the water. [/ QUOTE] I fill the pipe. When I use the glass water, it starts to drip slowly. You will see if you follow the thinner decreases over time. [/ QUOTE] I did what you said and removed the bumper and examined it, but I do not even have the slightest dropping, hodja. [/ QUOTE] It is true, but my teacher is that I use glass water without inserting the water pipe. It does not drip. As if the water is overpowering, carrying the water in the tank, I could not understand at all :) I also use antifreeze glass water. By opening the front clips of the right drum without removing the bumper, you could reach the glass water tank if you hurted slightly. your workmanship has been troublesome.

08.05.2020 20:31	# 12
ggitaristt
I had this problem when I first bought it. I cleaned it and put it on again and missed it again .. But it hasn't missed for the last 2 years.

08.05.2020 20:31	# 13
x571
I don't know when I put the water in the tank, but you didn't know 1, it's been 2 months. I recently ran the wiper water. There was a stench around him. as if someone fled. water got on my hand and washed 3 times that smell didn't go away what causes this smell? It has never happened to me.

08.05.2020 20:31	# 14
Peugeot35
[QUOTE = ggitaristt] I had this problem when I first got it. I cleaned it and put it on again and missed it again .. But it hasn't missed for the last 2 years. [/ QUOTE] exactly, my teacher is not a problem, it draws my attention to the pipe when it fills up, if it does not leak, then what happens is that it does not discard the water when there is less water in the pipe, as I said, I will either use it twice a month or not.

08.05.2020 20:31	# 15
ggitaristt
[QUOTE = x571] I don't know when I put the water into the tank, but you did not know 1 has been 2 months. I recently ran the wiper water. There was a stench around him. as if someone fled. water got on my hand and washed 3 times that smell didn't go away what causes this smell? It has never happened to me. [/ QUOTE]

08.05.2020 20:31	# 17
ALLEX
I read the subject to the last letter. It was an interesting but very interesting subject. I would like to thank everyone who showed interest and shared their ideas for the effort, sharing the pictures, comments.

08.05.2020 20:31	# 19
Orcun.Dmr
[QUOTE = Peugeot35] [QUOTE = 307 1.4 hdi] [QUOTE = Peugeot35] [QUOTE = 307 1.4 hdi] I fill the pipe until it is full. There is nothing like overflow or draining the water. [/ QUOTE] I fill the pipe. When I use the glass water, it starts to drip slowly. You will see if you follow the thinner decreases over time. [/ QUOTE] I did what you said and removed the bumper and examined it, but I do not even have the slightest dropping, hodja. [/ QUOTE] It is true, but my teacher is that I use glass water without inserting the water pipe. It does not drip. As if the water is overpowering, carrying the water in the tank, I could not understand at all :) I also use antifreeze glass water. By opening the front clips of the right drum without removing the bumper, you could reach the glass water tank if you hurted slightly. your workmanship has been troublesome. [/ QUOTE] The reason for disassembling the bumper is that I pulled the fog lamp installation and adjusted the places, I said let me look at it when it was ready to disassemble it, but what came to my strange came to me when the color of your water tank was black, not transparent plastic. Glad you did the dropping problem.

08.05.2020 20:31	# 20
sonerkyl
It really felt strange to puncture that tank. If you go to the health industry with your hands, no master will change unless you are very friendly. It cost you free.