![]() ![]() |
|
![]() |
307 does not work ... :( |
• Homepage » PEUGEOT MODELS (FAULTS AND SOLUTIONS) » 307 |
08.05.2020 16:11 | # 1 |
![]() |
|
I was just down to get an air like this, I started the car and the car didn't work. My car usually holds a lot of gasoline with LPG, but I wonder I bought 5 liters of gasoline to see if & nbsp; gasoline may be exhausted. The result has not changed. The vehicle does not start and I looked at the gas pump, I removed the pipe from the hose and pressed the starter and the result is not gasoline. Is it normal to start pumping normally when we switch on the ignition? Also, I think the vehicle with Atiker LPG normally pressed the switch and works with lpg, but it didn't work, mine doesn't even light anyway, does yours burn on the atiker switch?
|
08.05.2020 16:11 | # 2 |
![]() |
|
Does it cause antipollution fault and catalytic converter fault? |
08.05.2020 16:11 | # 3 |
![]() |
|
no any errors. By the way, when we turn on the gas pump contact, does it start to pump gas? When I remove the pipe and press the contact, it does not send gasoline.
|
08.05.2020 16:11 | # 4 |
![]() |
|
When he turns the ignition just like that, he starts pumping, hit the pump with something like a screwdriver, gently try it, bmw would happen to us very often, and the pump failure would get better when he hit it a few times.
|
08.05.2020 16:11 | # 5 |
![]() |
|
The pins and sockets of the gas pump are rotting and breaking, I solder the cable from the bottom of the pin and use it without changing the pump (hold the gas key to start the gas and start the vehicle) |
08.05.2020 16:11 | # 6 |
![]() |
|
[QUOTE = VEDATDINC] Gas pump pins, the sockets are rotting and rupture, I solder the cable from the bottom of the pin and use it without changing the pump (hold the gas switch to start the gas and start the tool) [/ QUOTE] & nbsp; Vedat from this connector I think you're talking about. I pulled this connector, I couldn't pull it out. Where am I going to poke it and where do I solder it? & nbsp; Meanwhile it doesn't work when you press and hold the gas switch ... :( |
08.05.2020 16:11 | # 7 |
![]() |
|
On LPG vehicles, I sometimes heard that the pump can burn to stop working, even a circuit that stops the pump can be installed for it, does your pump work?
|
08.05.2020 16:11 | # 8 |
![]() |
|
the problem is that the pump doesn't work & nbsp; but I want to disassemble that socket and try it out because there is a problem as farewell as I think the pump is around 350 I think ... |
08.05.2020 16:11 | # 9 |
![]() |
|
[QUOTE = mitto] anyway the pump does not work & nbsp; but I want to disassemble that socket and try it because if there is a farewell, I think the pump is around 350 ... [/ QUOTE]Insha'Allah it is not a pump. make it easy ... |
08.05.2020 16:11 | # 10 |
![]() |
|
If you measure whether & nbsp; electricity is coming to the socket you showed first, the float is disassembled & nbsp; the pins of the pump, that is, the sockets (electrical connection ends are cylindrical pins), are broken and broken. tl |
08.05.2020 16:11 | # 11 |
![]() |
|
[QUOTE = mitto] [QUOTE = VEDATDINC] Gas pump pins, the sockets are rotting off, I solder the cable from the bottom of the pin and use it without changing the pump (press and hold the gas switch to start the gas) [/ QUOTE] & nbsp; < DIV> Vedat I think you're talking about this connector. I pulled this connector, I couldn't pull it out. Where am I going to poke it and where do I solder it? & nbsp; In the meantime it doesn't work when you press and hold the gas switch ...: (& nbsp; & nbsp; & nbsp; & nbsp; & nbsp; & nbsp; & nbsp; & nbsp; & nbsp; & nbsp; & nbsp; & nbsp; & nbsp; & nbsp; & nbsp; & nbsp; & nbsp; & nbsp; & nbsp; & nbsp; & nbsp; & nbsp; & nbsp; & nbsp; & nbsp; & nbsp; & nbsp; & nbsp; & nbsp; & nbsp; & nbsp; & nbsp; & nbsp; & nbsp; & nbsp; & nbsp; & nbsp; & nbsp; & nbsp; & nbsp; & nbsp; & nbsp; & nbsp; & nbsp; & nbsp; & nbsp; thick cables of gasoline gauge motorhome feed ends "600" width = "750" border = "0" /> [/ QUOTE] |