|
|
|
|
307 Cockpit Center Console |
| • Homepage » PEUGEOT MODIFIED PLATFORM » 307 | |
| 08.05.2020 14:05 | # 1 |
 hasimayaz |
|
|
C5FG26F1 - 307 REMOVAL - REFITTING TOP CENTER FACADE 1 - REMOVAL Remove: radio
Remove: 2 packing or handles on the side (1) top fabric Disconnect its connectors. Remove the upper center facade (3). 2 - REFITTING Follow the reverse order of removal steps. Check the operation of electrical equipment. C5FG2CF1 - 307 REMOVAL - REFITTING LOWER CENTER PANEL AND ASHTRAY SECTION 1 - REMOVAL Remove: radio
Remove: 2 fixing elements (1) gear lever boot Remove the lower middle panel (3). Remove the ashtray box after disconnecting the illuminator. 2 - REFITTING
After adjusting the position of the illuminator, reattach the ashtray box. Place the panel lower foot (3) on the floor console: at (A). Clip from the top. Continue insertion following the reverse order of removal steps. |
|
| 08.05.2020 14:05 | # 2 |
 Guests |
|
|
thanks for sharing master
|
|
| 08.05.2020 14:05 | # 3 |
 ErkanKurnaz |
|
|
you have signed your signature again, the health supper sharing his master labor 
|
|
| 08.05.2020 14:05 | # 4 |
 mrtyrgr |
|
|
friends, please help on a subject 1999 model 306 xn I have the calirofer radiator of the car broke out, we left it to the mechanic to replace it, but the cockpit pinball lungur is shaking, how can I stop this swing?
|
|
| 08.05.2020 14:05 | # 5 |
 alpbeyazi |
|
|
the whole consul is cracked up and removed with care 
|
|
| 08.05.2020 14:05 | # 6 |
 tayfur |
|
|
friends, I could not fully understand this, I have to disassemble the gray part at the top, when I look at the pictures, there are 2 buttons at the top, how are they removed, I disassembled the tape, but at the bottom I could not see a screw type
|
|
| 08.05.2020 14:05 | # 7 |
 gorkemteke |
|
|
I will make carbon coating at the weekend, if I ask the inner console, I tried with this semester.
|
|
| 08.05.2020 14:05 | # 8 |
| tayfur |
|
|
I coated carbon, but I can't take it back when I think about removing it, We start the disassembly and assembly work first from the tape, I think you know how to remove it, then we remove the ashtray, open the 2 screws seen, the lower part pulls out a little to ourselves There is a nail there in the gearbox and it looks like the picture. then we will see 2 screws to remove the upper part, exactly because there is no other screw in the region where the cd player is installed, it catches your eye, We remove the right-most and left-hand keys on the top of the quadruple with 2 units. Whatever you say, I tried with a credit card and a thin-tipped screwdriver. and you both removed it, now you will need to remove the quad and the lock button, something with a claw, as if there is no need for a recipe anyway. When you make a carbon coating, you will need to file very little around the lock button, when the carbon is covered, the button is kept pressed. If you look at how to do it, you will have more or less ideas, I tried to explain so much at 2 o'clock in the night.  |
|
| 08.05.2020 14:05 | # 9 |
| gorkemteke |
|
|
Thank you, if I am not able to call you, I will have a chance to call you :)
|
|
