|
|
|
|
307 amp installations? |
| • Homepage » PEUGEOT MODIFIED PLATFORM » Peugeot Sound Systems | |
| 08.05.2020 17:53 | # 1 |
 Alicilik |
|
|
everybody had a share of his own. |
|
| 08.05.2020 17:53 | # 2 |
 s.seckin |
|
|
first of all, the left wiper is removed and the layer underneath (I don't know its name) behind the fuse box, when we remove our cable from the wiper arm and there is a stopper with black rubber, we remove the compartment with the headlight height adjustment inside the vehicle and the cable is just across the door and the cable is a wonderful transition point. After we have passed our cable that needs to be taken care of, we fill it with silicone thoroughly so that it does not let water in. It is a very important place. Quote from a post in the forum bro
|
|
| 08.05.2020 17:53 | # 3 |
 reality59 |
|
|
If the master does not get through there or after the beautiful isolate, the BSI is malfunctioning. There is a hole in the back of the gas pedal, covered with a plastic material, if you can, pass it there. Good work...
|
|
| 08.05.2020 17:53 | # 4 |
| Alicilik |
|
|
[QUOTE = onurazg a] I guess he was in the engine part of your vehicle ?? my car is in the car .. there are those who say that the battery will be drained or not even want to get into the battery business .. [/ QUOTE] I remember the same conversation before, well.  We are also under BSi Steering. There is a short wide cover under the steering wheel, and the entire steering wheel is exposed. Orkun was approximately in the same place as the brother (307XSi). When I opened the hood and looked at it, there was a plastic piece on the back of the right helix, I removed it, I looked at it, I extended a hole entering the car, I looked at it from the inside, it was just behind the BSi. In 207 of the cousin, the people who passed the door hinge, swore, took a photo and shared it.
|
|
| 08.05.2020 17:53 | # 5 |
 metin |
|
|
Hello there. In the photo, you can remove something like a stopper just at the bottom right of the heating pipe and pull the installation cable from there.
 |
|
| 08.05.2020 17:53 | # 6 |
 EnSoNiQ |
|
|
teacher, if you have cold silicon in your hand, do not bother with the back of the gas pedal, I think while laying the cable harness, the other parts go to the harder. It does not cause any problems, I use it as a dead one.
|
|
| 08.05.2020 17:53 | # 7 |
 fexzi |
|
|
drill the lower part of the boiler, drill the bottom plastic, then close it with dyson, so it is me now.
|
|
| 08.05.2020 17:53 | # 8 |
| fexzi |
|
|
Aha I saw the text :) brother welcome :)
|
|
| 08.05.2020 17:53 | # 9 |
| reality59 |
|
|
[QUOTE = onurazgin] [QUOTE = reality59] Do not miss the master, or after you pass the beautiful isolate, the BSI malfunctions if it gets water. There is a hole in the back of the gas pedal, covered with a plastic material, if you can, pass it there. Good work ... [/ QUOTE] Should we go through the hole in the back of the accelerator pedal, should I insert the inner plot or from the discharge? [/ QUOTE] You can see from the inside, it becomes easier, you have to do it by feeling the work you do from outside.
|
|
| 08.05.2020 17:53 | # 10 |
| metin |
|
|
Yes, we are talking about the same thing (: Already when he disassembles the air filter pipe at the inlet of the throttle, he will come across. |
|
| 08.05.2020 17:53 | # 11 |
| metin |
|
|
Thank you Fevzi. How was your health ? I hope you got it together.
|
|