306 Signal arm maintenance

If you hear a ticking sound from the signal role as it signals a stop in the vehicle, and if the signal stops moving or decreases when the signal lever moves, the major cause of the malignation will be the signal arm malfunction ... This happened in my vehicle before, and I will fix the malfunction as I tell you. I pulled around. There are 2 small screws fixing the signal arm to the plastic box on the steering wheel. Screws are always known as torque. I removed the screws. started to move in his sled. I pulled a little to the left and removed the 2 sockets on the back by pressing on its fingernails. If you do, don't take it directly because it doesn't. you need to press your nails well. then it comes off very easily. Anyway, when the sockets come out, the arm is left empty. I had a hard time pulling the lever out of the sled. Because it was attached to the left side of the torpot and I was able to pull the handle out of the sled by lowering the steering from the height adjustment and running the head. you need to dominate while removing it from the sled. In the meantime, you can break the box. After taking the handle out, there is a top and bottom cover. In the 1st picture, I saw the nails on the sides of the upper cover by blending them with a thin screwdriver. meanwhile be slow and careful. You will see 2 bows. you can throw these bows and lose them. this time, when you freeze post-signal steering, avoid the pain. The second picture is the first sore of the cover. then I pulled it out on my arm and saw the incident. In the third picture, you see the arm pulled out. In the 4th picture, the metal tip seen in the 5th picture moves by sliding in the gantry seen in the left part. The tip that normally stops in the middle completes the circuit by swiping in the upward movements and enables the signal to work. fabrication here is greasy. Now let me come to the cause of the event. The metal tip seen in 4 pictures is normally round-shaped. But it has been worked for years and has been swept up and has been hanged from 2 sides naturally thanks to its v-sectional structure and it has a v-shaped round circle. Of course where will these hanging parts go ??? It has become an institution by mixing with the grease around. this institution has become increasingly contacted. started to create a contact as well. Although we do not move the signal arm, the contact formed by the oil of that etched metal powder creates its voice in this role. I have the light of my soul, I put a thin cloth on the tip of the flat screwdriver and clean all these institutions as seen in the 5th picture. I wish I could picture it in the first carpet, you would understand better. but I couldn't think of it as I was quickly cleaning it. Then, I applied a small amount of grease to the cleaned place again and quickly closed the cover and put it on. Everything is frozen to normal. He is working hard. I would take a ohh. Because 75 TL was left in my pocket ... this arm would go 10 years more. Maybe after 5 years, I will do it again without wearing it. I send my best wishes behind the masters who say "we will replace the broken one" without looking at all as usual. They make us cost money, just like making money easily. there are no honest ones but very few. these masters are out of my words ... General view of the signal arm The bitter carpet of the role cap The arm is taken out of the arm You see the ball at the end of the arm. by hanging it tearing its roundness and getting the V shape. the interior of the canal cleared carpetcecoli2011-04-13 12:14:34

super shares your health

My favorite thing is that the horn is on the arm, not on the steering wheel. I think it is much more beautiful.
Thank you for this useful information and detailed explanations.

you are welcome friends

[QUOTE = cecoli] I would like friends. [/ QUOTE] I think it's more comfortable at the wheel. I used the last friend 106, I used the horn, I got used to the steering wheel, my hand went to the wheel, but it didn't sound because the horn was in the arm :)

[QUOTE = tigerland] [QUOTE = cecoli] I would like friends. [/ QUOTE] I think it's more comfortable at the wheel. I used my last friend 106, I used to press the horn, I got used to the steering wheel, but it didn't sound because the horn was on the arm:) [/ QUOTE]

my brother had the same problem I was looking at the prices on the internet, I found your share to change, I did the application, there was no problem. I joined the forum to thank you and the forum. thank you for your effort

This arm clearing event, which is valid within 206, is my contactless in the meantime ...

they always say "there is no such thing" just like that. I also had the same problem and I said, let me take a look at the site while looking at the prices on the internet like thelasthalil. You are super sister ..

the operation is ok. The sound that made me annoy and cause me to search for a signal handle was resolved just like in the same description. thank you so much...

Hello
I have the same problem in my vehicle. 306 Griffie. Master said that you will get a signal arm without fog lamp. I will send this information to him.