306 Not Working ... - 306

My car has many hardware deficiencies but there was no problem in its operation. When I came to Pendik from Beylikdüzü the other day, the temperature increased and I looked right on the highway. The heater hose touched the manifold and exploded from the heat. There was a new hose in the trunk, I installed it and solved the problem and added water. I started the car very normally and returned home. During the trip, the temperature was a little high, but my heater was blowing cold. Other than that, I returned home without any trouble. However, I could not start the car the next morning. It feels like it will work but it doesn't work. I have done 60-70 starter attempts at intervals in the last 2 days, but I was able to run only once. He also worked as PIT PIT PIT and I had to stop it when I heard violent PAT PAT sounds from the engine. It didn't work any more. I found an oil slick inside the cable of one of the spark plugs. Could it be because the oil has escaped? Since I could not remove the spark plugs, I tried to clean the spark plug seat by inserting a cloth with a screwdriver, but it did not help. Where might this problem originate from? When I stopped in the evening, the engine looked pretty normal :(

Can I do any damage if I find, remove and clean the spark plug key?
B-Devi 2011-10-27 19:33:43

My friend is not a mechanic, but since this incident happened to me in many of my vehicles, I am just writing my opinion.

& nbsp;

The overheated vehicle burns the top cover gasket, which means that the vehicle will mix water into the oil, which you can understand when it pulls the oil. The vehicle was operated yesterday evening. There is no problem because the piston has not accumulated water on the top, but the water accumulated on the piston all night, and the vehicle does not start.

& nbsp;

My advice to you is to try to start the vehicle directly. My opinion with the master is that the top cover will be removed, the gasket will change and you will continue from where you left off, if the vehicle is more km or there is wear in the water channels, I think that the upper cover gasket will handle the work, but I don't think it is a very expensive thing.

& nbsp;

This is the narrative that I wrote about the events that happened to me, it is not a definite thing, a master will say the best greetings. May Allah hide from it.

About 2 weeks ago, the upper cap hurt, the gasket and studs completely replaced. I gave 750 TL. This is the first heat after that incident. I think the gasket is not burned.

Replace the gasket now, start the car, the heat will burn, so it does not mean that it has not been burned 2 weeks ago.

There are some vehicles that get hot, but it does not burn the gasket, and sometimes even a little heat, the gasket can be burned.

As I said, this is only my opinion from my experience, the real problem will tell you when you see the master, or as I said, pull the oil cub and look at the oil condition, if the car is mixed with water, the seal is burned.

Get it easy now.

I looked at the oil of the car, it's just fine. Also, I looked at the water in the radiator and there was no oil residue. Are there any other symptoms I don't know

I couldn't get my job done with that car. He always said that the problem is always the problem.

If I find the spark plug wrench, remove the spark plugs and clean them, would I do any harm?

According to my opinion, you cannot go to a result by inserting and cleaning the spark plugs.
If I were at your place, I would bring the master who changed the gasket back. Also why is the heater hose not in the manifold? Is it wrong to wear it?

When I had the engine built, I also replaced the hoses. I think they couldn't fix it well and the hose melted over time. I took the increased hose with me as to what happens. I got it better ....

By the way, even if the gasket burned, I did not understand why it was not working. We wandered in a burned state for a week and there was no problem except heat. We were just constantly putting water on the vehicle
B-Devi 2011-10-28 13:15:58

Actual ....

I need your opinion on the subject, friends ...

The master engine has a gas contactor close to the wiper, a red button looks clear, it comes to my mind, but I still say you take it to a master

Get well soon, my brother, I hope it doesn't have a very costly problem and you can fix it immediately :(

I started the car today but it seems like 3 cylinders are working. He's working like a blast and the speed is low

08.05.2020 16:18	# 2
Serdar
My friend is not a mechanic, but since this incident happened to me in many of my vehicles, I am just writing my opinion. & nbsp; The overheated vehicle burns the top cover gasket, which means that the vehicle will mix water into the oil, which you can understand when it pulls the oil. The vehicle was operated yesterday evening. There is no problem because the piston has not accumulated water on the top, but the water accumulated on the piston all night, and the vehicle does not start. & nbsp; My advice to you is to try to start the vehicle directly. My opinion with the master is that the top cover will be removed, the gasket will change and you will continue from where you left off, if the vehicle is more km or there is wear in the water channels, I think that the upper cover gasket will handle the work, but I don't think it is a very expensive thing. & nbsp; This is the narrative that I wrote about the events that happened to me, it is not a definite thing, a master will say the best greetings. May Allah hide from it.

08.05.2020 16:18	# 4
Serdar
Replace the gasket now, start the car, the heat will burn, so it does not mean that it has not been burned 2 weeks ago. There are some vehicles that get hot, but it does not burn the gasket, and sometimes even a little heat, the gasket can be burned. As I said, this is only my opinion from my experience, the real problem will tell you when you see the master, or as I said, pull the oil cub and look at the oil condition, if the car is mixed with water, the seal is burned. Get it easy now.

08.05.2020 16:18	# 8
koliva
According to my opinion, you cannot go to a result by inserting and cleaning the spark plugs. If I were at your place, I would bring the master who changed the gasket back. Also why is the heater hose not in the manifold? Is it wrong to wear it?

08.05.2020 16:18	# 11
insomnia
The master engine has a gas contactor close to the wiper, a red button looks clear, it comes to my mind, but I still say you take it to a master

08.05.2020 16:18	# 12
I Love My Pug
Get well soon, my brother, I hope it doesn't have a very costly problem and you can fix it immediately :(

	306 Not Working ...
• Homepage » PEUGEOT MODELS (FAULTS AND SOLUTIONS) » 306

08.05.2020 16:18	# 1
B-Devi
My car has many hardware deficiencies but there was no problem in its operation. When I came to Pendik from Beylikdüzü the other day, the temperature increased and I looked right on the highway. The heater hose touched the manifold and exploded from the heat. There was a new hose in the trunk, I installed it and solved the problem and added water. I started the car very normally and returned home. During the trip, the temperature was a little high, but my heater was blowing cold. Other than that, I returned home without any trouble. However, I could not start the car the next morning. It feels like it will work but it doesn't work. I have done 60-70 starter attempts at intervals in the last 2 days, but I was able to run only once. He also worked as PIT PIT PIT and I had to stop it when I heard violent PAT PAT sounds from the engine. It didn't work any more. I found an oil slick inside the cable of one of the spark plugs. Could it be because the oil has escaped? Since I could not remove the spark plugs, I tried to clean the spark plug seat by inserting a cloth with a screwdriver, but it did not help. Where might this problem originate from? When I stopped in the evening, the engine looked pretty normal :( Can I do any damage if I find, remove and clean the spark plug key? B-Devi 2011-10-27 19:33:43

08.05.2020 16:18	# 10
B-Devi
Actual .... I need your opinion on the subject, friends ...

08.05.2020 16:18	# 13
B-Devi
I started the car today but it seems like 3 cylinders are working. He's working like a blast and the speed is low