306 minor maintenance + spark plug - 306

Hello
I said I'll take care of it today

trw rear brake disc suit 54 tl
trw rear lining suit 41 tl
bosch platinum lpg spark plug, 14 tl
elfren wire right left tool 40 tl
bosch oil filter 12 tl
bosch petrol filter 15 tl
fuji air filter 10 tl
castrol magnatech 10/40 oil 4.5 lt 60 tl

90 TL of montage money that I gave to the master

90 lira workmanship hicbisey for these. Let's be beautiful, my country. Gule gule old age sec. tugrah that.

Good luck, use good bye. If you share your opinion on behalf of trw disk and balata team in our time, let us know. Because some of them are not satisfied with trw, some say it is no different from the original ...

Why did you replace the hand brake wires ??? is it broken or another problem ???

in the cold in the winter, the brake was stuck
I even shared it here
wire creep and occasionally tighten the right wheel
Here we burn the pads
we changed the wire to the complete disc pad
my master is very good, we put it on the talk slowly in 3 hours
it is right that money

cecoli I couldn't find the motor oil you suggested.
I had an elf in the master.
and he didn't want me to use the engine cleaner additive
He said it would cause problems elsewhere while cleaning the room.

I respect our master :))

Washing the engine is not so necessary anyway. There is nothing to use with the province. In oil, 10-40 magnatec is not an oil anyway. but you could use better. anyway use good bye. Do not forget to share the subject of brake in the future :))

Could it be because the hand brake remains pulled on if the pads are frozen? Because if the hand brake is pulled too cold in the cold, the pads can freeze. this time it does not release the handbrake if you lower it. I wonder if such a situation came to the press. ???

no matter what he deserves, the right side is sometimes slightly boring in my car. I am thinking to control the wires. I officially notice this because sometimes it doesn't flow where it needs to flow very lightly. Sanki hand brake as if the outer one was left ...

I left the handbrake when it came to work in the evening in a very cold weather in winter.
I wont get down that elfren in the morning and went to work my workplace is 4 km
there is a slope on the road at the end, the crotch usually takes the middle gear down
slow down in the car like the previous ones, the car did not flow, slowly came down I felt there
when I got to the parking lot there was a heavy smell and the warm caliper and the buzz of the pad but only on the right wheel
the other one left and there was a wire creep and lost its form
One day, that smell came right, I went to the master locked one by one when the right saved the filament wire.
returned to normal, of course, it is impossible to find the wire here.
Thanks to our sponsor Şahin, I have supplied the peugeot at an affordable price.
I was going to buy bosch or valeo disk, my master especially wanted trw.
I also bought it from otostart.com during the month of April, there is a 20% discount and free shipping campaign for purchases of 50 TL and above.

what brand was it coming out of? trw fold what you call it quality) :) or what do you think it is? For example, I have heard of trw output in some of the original materials used in the service ... I wonder if this trw service material produces lower quality and does it give the market a lower quality product?

They say they are very hard for trw pads. you test your test and share. though the top out of the trw umim ... :)) the cecol 2011-04-13 09:19:07

What is the brand of the original pad? I asked for the last clutch pressure pad, they said take VALEO. I had bought the starter dynamo automaton before. Or is it VALEO?

[QUOTE = badires] What is the brand of the original pad? I asked for the last clutch pressure pad, they said take VALEO. I had bought the starter dynamo automaton before. Or is it VALEO? [/ QUOTE]

The original is not certain. Because when Peugeot understands with whom at that time, he buys and wears that brand.

valeo, lucas, bosch, bendix, trw or something ... let's say that the vehicle came out of the lucas. then if you go to the service and get the original, it can be valeo :)))

I know they have different quality in the valeo clutches. There is also a local valeo. I have imported valeo too ... I know if it shows variability ...

We couldn't meet the lpg spark plugs, brother (:

cem bro you said that the low speed traction is very good, did you calculate the fuel?

It was a very nice care.

lpg spark plugs you wrote 10 tl I gave 56 tl: S

[QUOTE = 60de106] You wrote 10 ll spark plug spark plugs, I gave 56 TL: S [/ QUOTE]

The friend has written 14 TL above, as well as 56 lira already :))

Where is 10 TL written ???

[QUOTE = Serhun] It was a very nice care, use bye. [/ QUOTE]
thanks my friend

[QUOTE = 60de106] You wrote 10 ll spark plug spark plugs, I gave 56 TL: S [/ QUOTE]

I added to the basket 1 day ago on the internet then it was 13 TL
they made a 20% discount and free shipping when buying the day after
but they just made the spark plug 16-odd, here is 13-odd with 20% discount

we've done the lpg setting this day
If the manifold was getting air from the nozzle, it was found by my engine master.
When the maintenance was over, we went to the test at lpg and the vehicle did not eat good gas at high speed.
He realized that he forced it very hard and the vehicle switched to gasoline and poured water in the idle manifold.
and at the entrance of the 2nd lpg pipe, the engine made a different sound
I went to the lpg service, the nozzle was dismantled, put a substance and put it back on, we waited for it to dry a bit
It was checked if it was getting air again and then we went on test drive and the car was connected to the computer.
They did the road test as well and got me behind the wheel to try it, sudden gas reactions were knocking, he was having a hard time going up and he was throwing gasoline
the vehicle that has gone is running very stable and more enthusiastic than before

I also bought the idling sensor, but I did not install it, I wanted to see the effect of the lpg spark plug
I saw that the idling ripple was gone, which means that the lpg spark plug draws less voltage than the attachment coil, I had read on a site that it uses 20% less electricity than the gas spark plug.
I think this is real
I tried the lower revs, for example, the idling of my vehicle was 900 - 800 rpm when the engine was hot.
In the 3rd gear, I give the gas at 1000 rpm on the straight road without any difficulty or knock.
I am trying to accelerate again, I throw the 4th gear at 2500 rpm in 3rd gear and fall down to 1000 rpm.
I give gas at 1000 rpm, don't expect miracles again, but there is a benefit

I don't think it will affect the fuel very much because the amount of fuel that enters the engine is the same, if only 80% of the fuel that enters the cylinder with the stock spark plug is discharged without burning.
something like 95% burning with that biji probably

What did they do to you because of this assembly? I was talking about them when I said assembly quality. Whatever happened, things had happened. I hope it will not cause any problems. more...

You say brother, you say, I would kiss your hand if I found somebody who assembled like this.

do you know about these
learning
dont ask
take your gas
go to bass
Believe me, I am in the industry for every month of leave for 1 month.
But I was stubborn, I even complained to the top management of BRC.
I put the pictures of the assembly on the site, I put yours on the look, atiker assembly you do not like
I said, did you see this, I said, do you see a difference in the installation of 2a authorized service? What do you say

how painful, but real, some of our trades are lakite, insistent and cakal ...

Shame on the people of this mill. As I see and hear such things, my scraps go up. nobody wants to heat up well. nobody wants to make effort. "Give me eat, sleep, sleep" account wants to live free of charge ...

Ah Atam, get up, once you say "Turk pretend is running, he is clever".

08.05.2020 15:15	# 1
tugrahan
Hello I said I'll take care of it today trw rear brake disc suit 54 tl trw rear lining suit 41 tl bosch platinum lpg spark plug, 14 tl elfren wire right left tool 40 tl bosch oil filter 12 tl bosch petrol filter 15 tl fuji air filter 10 tl castrol magnatech 10/40 oil 4.5 lt 60 tl 90 TL of montage money that I gave to the master

08.05.2020 15:15	# 2
koliva
90 lira workmanship hicbisey for these. Let's be beautiful, my country. Gule gule old age sec. tugrah that.

08.05.2020 15:15	# 4
tugrahan
in the cold in the winter, the brake was stuck I even shared it here wire creep and occasionally tighten the right wheel Here we burn the pads we changed the wire to the complete disc pad my master is very good, we put it on the talk slowly in 3 hours it is right that money cecoli I couldn't find the motor oil you suggested. I had an elf in the master. and he didn't want me to use the engine cleaner additive He said it would cause problems elsewhere while cleaning the room.

08.05.2020 15:15	# 5
Guests
I respect our master :)) Washing the engine is not so necessary anyway. There is nothing to use with the province. In oil, 10-40 magnatec is not an oil anyway. but you could use better. anyway use good bye. Do not forget to share the subject of brake in the future :)) Could it be because the hand brake remains pulled on if the pads are frozen? Because if the hand brake is pulled too cold in the cold, the pads can freeze. this time it does not release the handbrake if you lower it. I wonder if such a situation came to the press. ??? no matter what he deserves, the right side is sometimes slightly boring in my car. I am thinking to control the wires. I officially notice this because sometimes it doesn't flow where it needs to flow very lightly. Sanki hand brake as if the outer one was left ...

08.05.2020 15:15	# 6
tugrahan
I left the handbrake when it came to work in the evening in a very cold weather in winter. I wont get down that elfren in the morning and went to work my workplace is 4 km there is a slope on the road at the end, the crotch usually takes the middle gear down slow down in the car like the previous ones, the car did not flow, slowly came down I felt there when I got to the parking lot there was a heavy smell and the warm caliper and the buzz of the pad but only on the right wheel the other one left and there was a wire creep and lost its form One day, that smell came right, I went to the master locked one by one when the right saved the filament wire. returned to normal, of course, it is impossible to find the wire here. Thanks to our sponsor Şahin, I have supplied the peugeot at an affordable price. I was going to buy bosch or valeo disk, my master especially wanted trw. I also bought it from otostart.com during the month of April, there is a 20% discount and free shipping campaign for purchases of 50 TL and above.

	306 minor maintenance + spark plug
• Homepage » PEUGEOT MODELS (FAULTS AND SOLUTIONS) » 306

08.05.2020 15:15	# 10
metin
We couldn't meet the lpg spark plugs, brother (:

08.05.2020 15:15	# 12
metin
cem bro you said that the low speed traction is very good, did you calculate the fuel?

08.05.2020 15:15	# 14
Guests
lpg spark plugs you wrote 10 tl I gave 56 tl: S

08.05.2020 15:15	# 15
Guests
[QUOTE = 60de106] You wrote 10 ll spark plug spark plugs, I gave 56 TL: S [/ QUOTE] The friend has written 14 TL above, as well as 56 lira already :)) Where is 10 TL written ???

08.05.2020 15:15	# 16
tugrahan
[QUOTE = Serhun] It was a very nice care, use bye. [/ QUOTE] thanks my friend

08.05.2020 15:15	# 17
tugrahan
[QUOTE = 60de106] You wrote 10 ll spark plug spark plugs, I gave 56 TL: S [/ QUOTE] I added to the basket 1 day ago on the internet then it was 13 TL they made a 20% discount and free shipping when buying the day after but they just made the spark plug 16-odd, here is 13-odd with 20% discount we've done the lpg setting this day If the manifold was getting air from the nozzle, it was found by my engine master. When the maintenance was over, we went to the test at lpg and the vehicle did not eat good gas at high speed. He realized that he forced it very hard and the vehicle switched to gasoline and poured water in the idle manifold. and at the entrance of the 2nd lpg pipe, the engine made a different sound I went to the lpg service, the nozzle was dismantled, put a substance and put it back on, we waited for it to dry a bit It was checked if it was getting air again and then we went on test drive and the car was connected to the computer. They did the road test as well and got me behind the wheel to try it, sudden gas reactions were knocking, he was having a hard time going up and he was throwing gasoline the vehicle that has gone is running very stable and more enthusiastic than before I also bought the idling sensor, but I did not install it, I wanted to see the effect of the lpg spark plug I saw that the idling ripple was gone, which means that the lpg spark plug draws less voltage than the attachment coil, I had read on a site that it uses 20% less electricity than the gas spark plug. I think this is real I tried the lower revs, for example, the idling of my vehicle was 900 - 800 rpm when the engine was hot. In the 3rd gear, I give the gas at 1000 rpm on the straight road without any difficulty or knock. I am trying to accelerate again, I throw the 4th gear at 2500 rpm in 3rd gear and fall down to 1000 rpm. I give gas at 1000 rpm, don't expect miracles again, but there is a benefit I don't think it will affect the fuel very much because the amount of fuel that enters the engine is the same, if only 80% of the fuel that enters the cylinder with the stock spark plug is discharged without burning. something like 95% burning with that biji probably

08.05.2020 15:15	# 18
Guests
What did they do to you because of this assembly? I was talking about them when I said assembly quality. Whatever happened, things had happened. I hope it will not cause any problems. more...

08.05.2020 15:15	# 19
tugrahan
You say brother, you say, I would kiss your hand if I found somebody who assembled like this. do you know about these learning dont ask take your gas go to bass Believe me, I am in the industry for every month of leave for 1 month. But I was stubborn, I even complained to the top management of BRC. I put the pictures of the assembly on the site, I put yours on the look, atiker assembly you do not like I said, did you see this, I said, do you see a difference in the installation of 2a authorized service? What do you say

08.05.2020 15:15	# 20
Guests
how painful, but real, some of our trades are lakite, insistent and cakal ... Shame on the people of this mill. As I see and hear such things, my scraps go up. nobody wants to heat up well. nobody wants to make effort. "Give me eat, sleep, sleep" account wants to live free of charge ... Ah Atam, get up, once you say "Turk pretend is running, he is clever".