|
|
|
|
306 Maintenance of blocked water drains |
| • Homepage » PEUGEOT MODIFIED PLATFORM » 306 | |
| 08.05.2020 15:15 | # 1 |
 Guests |
|
|
As friends have in every vehicle, 306 has its own points to be considered. one of them is the water expense on the right and left of the glass. These points where the water flows are bigger than about 1 TL. These holes become clogged over time with the collection of dried leaves, etc., and the water stops flowing. Together, those sections can fill up inside the vehicle like a pool, cause electrical problems, erase, and damage parts such as a heating engine. At this point, the cleanliness of these regions is important. In this case, since it was not taken care of by most users, I found it appropriate to share with you. First, we will start by inserting our arms to be wiped. We remove the caps on the bolts of the arms with a thin screwdriver. With the appropriate wrench or ratchet, we loosen and remove the nuts of the arm. some arms may be milled and some may be conical tightened. Then, by inserting a few screw screws on the grille on the glass, we remove the grills from their place. Then there is a black piece of sheet metal standing on the lower arms of the arms. In the 1st picture, with the carpet attached to its place, in the 2nd picture, it is seen as inserted above the engine. we take this out. The lower arms are combined with the motor to be wiped. There are 5 bolts for us to insert completely. We take them out and when we insert the socket of the engine, we take it completely from its place. Subsequently, the nest is completely emptied, as it is seen in the pictures. You can clean the inside well and collect it again ... You can do it simply, without inserting the motor to be wiped. When the vehicle is not wet, you can blow the air from the sides of the engine to wipe, so that the dried leaves come out of the flakes. then you can get air again by getting wet. and then you can control the flow of water by touching it with plenty of water. If the perforated hole does not hurt, you can try to hurt by inserting a wire etc. but remember that this is a short solution ... Because the engine to be erased is installed in its place, it does not get inside as you see in the 1st picture. it will be helpful if you have inserted the engine to wipe the erosion, and also take a good care of the arms and the engine. lubricating the necessary joint points will provide more comfortable working ...    The point inside the tool outside the vehicle.  The water on the right side goes. When the grille and the protective plastic are removed, the air intake into the heating engine is displayed.  On the left side of the engine that will be wiped in the bowl, the water flowing is the same as the hole ... When you look inside this grill, you see the green propellers of the heating engine and the motor valve that closes the outside air when you want it.  |
|
| 08.05.2020 15:15 | # 2 |
 koliva |
|
|
Thanks for information. Masallah clean tool 
|
|
| 08.05.2020 15:15 | # 3 |
| Guests |
|
|
I don't have so many tools. I have a flat screwdriver and a star screwdriver. I think I can't do it with them. I will have to take it out to the master. Can you also put a photo of the other side's disassembled?
|
|
| 08.05.2020 15:15 | # 4 |
 Serhun |
|
|
Brand model is not important, I recommend cleaning the system in many vehicles once a year. Thanks for informations.
|
|
| 08.05.2020 15:15 | # 5 |
 metin |
|
|
[QUOTE = badires] I don't have that much equipment. I have a flat screwdriver and a star screwdriver. I think I can't do it with them. I will have to take it out to the master. Can you put a photo of the other side's disassembled? [/ QUOTE] Instead of looking at the master and giving money to the master, you can take care of this and such problems by getting tools and equipment with that money;)
|
|
| 08.05.2020 15:15 | # 6 |
| Guests |
|
|
[QUOTE = badires] I don't have that much equipment. I have a flat screwdriver and a star screwdriver. I think I can't do it with them. I will have to take it out to the master. Can you put a photo of the other side's disassembled? [/ QUOTE] On the other side, don't worry my brother will add your pictures :)) In the meantime, start the preparations and get yourself a tool.
 |
|
| 08.05.2020 15:15 | # 7 |
| Guests |
|
|
@ badiress @ ugur clskn I added the right side of the grill ...
|
|
| 08.05.2020 15:15 | # 8 |
| Serhun |
|
|
Thanks for informations.
|
|
| 08.05.2020 15:15 | # 9 |
| Guests |
|
|
You are telling the truth. It is necessary to start creating a small toolbox. otherwise I wouldn't even be able to try most of what you told.
|
|
| 08.05.2020 15:15 | # 10 |
| Guests |
|
|
For example, you can start by buying a torque tool for the most common use in our vehicles :))
|
|
| 08.05.2020 15:15 | # 11 |
| Guests |
|
|
I don't even know what the torque suit is. Now I'm looking at it from google. |
|
| 08.05.2020 15:15 | # 12 |
| Guests |
|
|
I saw now. It has a pentagon or a hexagonal head. A simple tool. They made designs similar to the Swiss army knife.
|
|
| 08.05.2020 15:15 | # 13 |
| Guests |
|
|
star-shaped screws are called torque. you probably know the straight or the star. There is another model screw in torque. wherever you look in the vehicle, you can see. because there are many places :))))))))))) |
|
| 08.05.2020 15:15 | # 14 |
| Guests |
|
|
Yes I know. I know there are parts that you disassembled above. After your summer, I intended to star, I could not disassemble, I frightened and gave up lick. But apparently the charlotte was not to take it.
|
|
| 08.05.2020 15:15 | # 15 |
| Guests |
|
|
If you have a bauhaus near you, you can get a recharged screw from there or elsewhere, and a "flat" blade with various star torque ends to use with it. will see a lot of heat everywhere. The product is the same as the link. I advise. both good and strong and cheap ... it's 4.8V tour
|
|
| 08.05.2020 15:15 | # 16 |
| Guests |
|
|
Is there such a problem in 206's, master?
|
|
| 08.05.2020 15:15 | # 17 |
| Guests |
|
|
I did not see it in 206, but I did not see ... but the maintenance of water expenses is valid for every vehicle :)) If it gets clogged, the water becomes a lake :))) For example, in 206, there is water supply at the point where the right absorber press is at the point where the pollen filter is there. it is necessary to keep them clean ...
|
|
| 08.05.2020 15:15 | # 18 |
| Guests |
|
|
[QUOTE = CeCoLi] I haven't seen it in 206 ... but if the maintenance of water expense is valid for every vehicle :)), if it gets clogged, the water becomes a lake :))) For example, in 206, there is water supply at the point where the right absorber press is at the point where the pollen filter is there. it is necessary to keep them clean ... [/ QUOTE] well thank you :)
|
|
| 08.05.2020 15:15 | # 19 |
 redline |
|
|
While I had read this subject before, I think that it should be cleaned, as the rains started to rain these days, it gave me a wiper malfunction on the first day.
|
|
| 08.05.2020 15:15 | # 20 |
| Guests |
|
|
Thank you again for sharing Cem, there is a problem in the output of the wiper water in my vehicle too, I think it does not throw out enough water.
|
|