206 Sound Insulation and Pulley? - Peugeot Sound Systems

Sa friends first I bought a 16 cm hertz hsk 165 mid team the other day. the doors sat 16 cm but did not sit in depth. I had a pulley for 206 before, but this time, when I put it on the floor, it makes a whine, I guess the mid team hits the floor when it hits bass, limiting the movement. The flooring of the right door did not sit, the nails remained exposed, I guess, I calculated the wrong one while drilling the hoop. How can I make an application for the outside of the hoop? What kind of a solution has it been? Also, can pockets be made on the floor of 206? the pocket is not fixed there, but can they trade on it or anywhere else on the door?

The second issue is sound insulation. Now there is a situation like this. When the mid team hits bass, the cone moves yes, but the bass sound is too little and not too full, it sounds like a pit pit. I can feel the bass sound when I sit in the back seat. By the way, I'm talking about only mid team bass with the subwoofer off. If I do sound insulation, can I feel the bass sounds more in front and inside the car? can I feel a significant change in sound in general? How much would it cost if I had this job done by an outside company? What materials should I use if I do it myself? and what does it cost? Would it be enough if we make the insulation to the sheet under the floor? Or do we have to do the inner man? I think of making the front door of the vehicle only. Can experienced friends who have previously insulated help?

No friends making sound insulation? or did I open the subject to the wrong place: D

Since I do not understand from the sound system, I am overtaking Question 1 e. I'm going to the question.
I insulated my vehicle myself, if you have a free day and a bit of a hand, you can do it too. Although there is no sound system in my vehicle, after making insulation, the sound is now higher quality. If you buy bituminous tape as a material, a little thin sponge will be enough, you can connect 50 tl to 4 doors.

I'll just do 2 doors. measure the door length 90 cm width 50 cm. If I buy 1 ball bitumen, it feels like 10 meters to 20 cm 2 doors. I doubt it will spend bitumself as much as the outside of the door. Is there thermaflex as a sponge, would it work in the boat? The materials I found are the following.

http://www.tekzen.com.tr/ses_kesici_sunger_kopuk_levha_5mm_fire_/640261

http://www.adetasyapi.com/?=/bituself_oto_ses_yalitimi_-_bituself_oto_ses_ızolasyonu/&urun=1555

One ball is enough for 2 doors. Buy 30 cm if you can. I could not look at the sponge, I enter through the wire. Take the finer of the sponge.

[QUOTE = Piyanist89]

I do not remember the size [/ QUOTE] with a thickness of 10 mm, but there are two types, one is thin and one is thick, you need to take it thin.

I finished 1 door today, I could not put the sponge due to the time I went to the 2nd door. almost done. I opened music and listened, I couldn't see a difference. I knock on the sheet of the door, there is no satiety like before. I also go out and close the door when the music plays. When the subwoofer strikes, there is a whisper at the door. I said that the bass sounds of the mid team would improve a little more and there was no room. There is a problem with the material I use, or there are some places inside the door, there is no hand, I do not know. or there is an indispensable place at the door, we have missed it there. The materials I used are the same (same as 1.5 mm thick bitumen). I couldn't find the bitumselfi. I bought this one. I would like to share the pictures anyway. jpghttp: //i.hizliresim.com/pe9lm8.jpghttp: //i.hizliresim.com/78z0vl.jpghttp: //i.hizliresim.com/gla3on.jpghttp: //i.hizliresim.com/z14byg.jpghttp: //i.hizliresim.com/ozvdeq.jpghttp://i.hizliresim.com/lzlaeb.jpghttp://i.hizliresim.com/vydqey.jpghttp://i.hizliresim.com/m8byxy.jpghttp:// the i.hizliresim.com/eeoao9.jpghttp://i.hizliresim.com/jyzkqg.jpghttp://i.hizliresim.com/2qaxo0.jpghttp://i.hizliresim.com/b9ypoj.jpghttp://. I hizliresim.com/z14b50.jpghttp://i.hizliresim.com/ozvddo.jpghttp://i.hizliresim.com/lzlaql.jpghttp://i.hizliresim.com/vydqqq.jpghttp://i.hizlires. com / ngn8b1.jpg

I was thinking to do well in the hands of the master, but there was no courage. It was very nice. I was enthusiastic.

You also need to add insulation sponge on bitüself

08.05.2020 18:52	# 3
Barut
Since I do not understand from the sound system, I am overtaking Question 1 e. I'm going to the question. I insulated my vehicle myself, if you have a free day and a bit of a hand, you can do it too. Although there is no sound system in my vehicle, after making insulation, the sound is now higher quality. If you buy bituminous tape as a material, a little thin sponge will be enough, you can connect 50 tl to 4 doors.

08.05.2020 18:52	# 5
Barut
One ball is enough for 2 doors. Buy 30 cm if you can. I could not look at the sponge, I enter through the wire. Take the finer of the sponge.

08.05.2020 18:52	# 6
Piyanist89
10 mm thick

08.05.2020 18:52	# 7
Barut
[QUOTE = Piyanist89] I do not remember the size [/ QUOTE] with a thickness of 10 mm, but there are two types, one is thin and one is thick, you need to take it thin.

08.05.2020 18:52	# 9
atrix
I was thinking to do well in the hands of the master, but there was no courage. It was very nice. I was enthusiastic.

	206 Sound Insulation and Pulley?
• Homepage » PEUGEOT MODIFIED PLATFORM » Peugeot Sound Systems

08.05.2020 18:52	# 10
eyup ozturk
You also need to add insulation sponge on bitüself