206 right rear wheel

Hello, easy, guys. If the right rear side of the vehicle comes with a metal crashing sound, it feels like it is slanted from the top of the tire, it feels like it is playing in the pits, it is not clear, I was loading the video. Thank you already, I am loading pictures and videos in minutes. "/> [TUBE] C6thcNK_z-Y [/ TUBE] meteor 2017-06-28 15:11:57

problem torsion unfortunately my teacher

[QUOTE = sonerkyl] problem torsion unfortunately my teacher [/ QUOTE] burned, then as far as I learned from the forum, is it worth 500 TL :) I can do a long way in this way. not to come off the tire or something

[QUOTE = meteora] [QUOTE = sonerkyl] problem torsion unfortunately my teacher [/ QUOTE] burned then as much as I learned from the forum, 500 TL or something :) can I make a long way like that? the tire or something to come off [/ QUOTE]

[QUOTE = sonerkyl] [QUOTE = meteora] [QUOTE = sonerkyl] problem torsion unfortunately my teacher [/ QUOTE] burned, then as much as I learned from the forum, 500 tl or something :) can I do a long way in this way? the tire or something to come off [/ QUOTE] [/ QUOTE] I am most afraid of it. I am a student in bulgaria and find a master here is very difficult. thank you again

Brother, get it done tomorrow. Otherwise, the expense is multiplied. If I had it made early, you could save it with 200 TL. Now, even if you used a little more of the torsion slot, the balance rods, each of which was 300 TL, would even harm him. I think no delay. Or no riding kilic46 2017-06-28 20:16:25

[QUOTE = kilic46] Sister get it done tomorrow. Otherwise, the expense is multiplied. If I had it made early, you could save it with 200 TL. Now, even if you used a little more of the torsion slot, the balance rods, each of which was 300 TL, would even harm him. I think no delay. Or did you ever ride [/ QUOTE]? Does your vehicle sound like an iron like this?

The village was like a dolmus. 550 latheers, 160 balls, 140 shock absorbers, 150 TL labor.
Except those who steal selectors and horns from the back and say that they will come out one by one. There is no sound right now. No capture. A 10 years goes

[QUOTE = kilic46] The village had been filled with a brothers.550 turners, 160 balls, 140 shock absorbers, 150 TL labor.
Except those who steal selectors and horns from the back and say that they will come out one by one. There is no sound right now. No capture. It goes on for 10 years [/ QUOTE] I have no hope here, but tomorrow I will go to the service here, what are they going to say, how much will they say? thanks

First of all, hello friends, I have a point to consult, I have 206, and as the friend said, I heard a noise like rubbing metal from behind on all kinds of roads except asphalt. I asked a couple of places. But it has been rarely making that sound for four or five days. As if it suddenly recovered.

[QUOTE = mstfkrkmz61] First of all, hi friends, I have a point to consult, I have 206, and as my friend said, I was suspicious of torsion on all kinds of roads except asphalt. I asked a couple of places without looking at the sound without even listening to the sound. and he said he had to go to the turner, but he's been rarely making it sound for four or five days. As if he suddenly recovered. [/ QUOTE]

I hope a simple problem arises as you say ..

It was like a break in me now, but I am sure I couldn't find time to have it done because it is torsion. If there are defects in the bends in the bends, even jumping over is like jumping. The voice still continues to increase, meanwhile, as the friend says, he turned to the village minibuses :)

When the bends of the cornering nedege arm loosens, it hits the iron. Do not fill the torsion shaft with welding. If a motor master who knows his job will distribute the torsion comfortably and the balls will not change, let the lathe kiss you.

it comes from the right front wheel.

Don't look, I couldn't write for a long time, as Soner and his sword friend said, there was no problem in torsion. It kept a total of 800 TL, 450 lathes, 180 balls, I think the rest was suitable for me, except for the lathe :) Meanwhile, there are other small vibration sounds scattered throughout the exhaust, but let's see there is no time for now.

180tl parts 620tl total workmanship ... !!! Let these masters be blind, I am not saying anything else

[QUOTE = madblueblacksea] 180tl parts 620tl total workmanship ... !!! Let these masters be blind and say nothing else [/ QUOTE]

Where did you get it hodja

[QUOTE = tsufrankwoli] [QUOTE = madblueblacksea] 180tl parts 620tl total workmanship ... !!! Let these masters be blind and say nothing else [/ QUOTE]

Where did you get it hod [/ QUOTE]

I did not do this. Last year, I made 150 balls and 100 liters of workmanship to 250. I did not go to the screw driver, there was no problem with the shafts. If it did, I had no intention of welding the lathe. 100tl is already a pair of miles.

I made it in Kırklareli Lüleburgaz