(206+) removing the headlight

Guys,

There is something wrong with the dipped-beam headlamp of the left headlight so the bulb does not fit properly so there is almost 30 degrees difference between the right headlamp and it does not look down even at the lowest level. I have to fix it. Yesterday and today I studied a little in the morning, the slot has 3 feet, this is connected to the 3 foot headlight mirror, two of them came back a little. Since the headlight was not empty, I couldn't do it. I will take it off and make the headlight adjustment. When I look at the servicebox, there is a screw with a torque of 1 20 on the bottom and is it necessary to remove the bumper?

Removal - Installation: Headlight IMPERATIVE: Follow the safety and cleaning instructions. 1. Removal Disconnect battery connections. Remove the front bumper. FIGURE: Remove the c4am0v6d Socket (at the location indicated by "a"). remove the bolts (2). Unclip: Headlight (3) (at the location indicated by "b"); With the help of a small flat screwdriver. Remove the headlight (3). 2. Apply the reverse order of removal. Tighten the bolts (2) with a torque of 0.5 ± 0.1 da.N.m. CAUTION: Carry out the necessary actions after reconnecting the battery connections. Reconnect the battery. Adjust the headlights. Make sure that the equipment works electrically.

Removal - Installation: Front bumper IMPERATIVE: Follow the safety and cleaning instructions. 1. Preparation operations Disconnect the battery connections. NOTE: Place the vehicle on a two-column lift (to facilitate operation). Partially separate the front hoods. 2. Disassembly FIG: Remove the b1bm1bed bolts (1). FIGURE: c4am0xyd NOTE: Symmetrical operation (by equipment). Disable the front fog lamp (2) connector (at the location indicated by "a"). FIGURE: Remove the c4am0xzd bolts (3). FIGURE: Remove the c4am0y0d bolts (4). FIGURE: Remove the c4am0y1d bolts (5). FIGURE: c4am0y2d CAUTION: It takes 2 people to do the following operations. Separate then remove: Buffer (6) (in arrow direction). 3. Apply the reverse order of removal. Tighten the bolts (4), (5) with a torque of 0.8 da.N.m. Reconnect the battery. Check the operation of the equipment.

Control - Adjustment: Headlight IMPERATIVE: Follow the safety and cleaning instructions. 1. Recommended tools FIGURE: e5ap2zhd [1] regloscope: FACOM LUX 200L MULLER 664 LASER TECNOTEST 432 / PM 2. Control Vehicle empty. Vehicle ready to move (vehicle empty, tanks full). Remove any excess mud, snow or ice buildup that could affect the vehicle floor. Check the pressure of the tires. Inflate under normal road conditions at the pressure set by the manufacturer. Park the vehicle on a level surface with the wheels in full level. Turn on the headlights. Check the operation of the load corrector by turning the adjustment lever. Bring it to the normal load position "0". By applying a pressure to the rear of the vehicle and checking the stability of the light beam, check the operation of the automatic headlight adjusters when the headlights are on (depending on the equipment). FIGURE: c5em02fd (1) Headlight with halogen lamp. Start the engine. Align the headlamp ruler [1] with the vehicle (according to the headlight adjuster device). Align the center of the headlight ruler lens over the headlight's optical center (at the location indicated by "a") (Cap center); With the laser beam of the headlight adjustment device or with the bar of the headlight adjustment device (according to the headlight adjustment device). Turn on the dipped headlights. Continue checking according to the user manual of the headlight adjusting device. 3. Setting 3.1. Conditions before adjustment Perform the adjustment procedure of the headlight adjusting device according to the operating instructions of the headlight adjusting device [1]. FIGURE: c4am0v5d Record the refractive value of the headlight beam (1) (at the location indicated by "b"). Parameter the received value (according to the headlight adjustment device). 3.2. Setting method: Headlight with halogen lamp FIGURE: c5em07rd (1) Headlight with halogen lamp. NOTE: According to the equipment. Correct the headlight vertical adjustment (height) by acting on the screw (at the location indicated by "d"). Correct the headlight's horizontal adjustment (azimuth) by acting on the screw (at the location indicated by "c"). FIGURE: c5em07sd Align the beam's light beam e slightly below the separation line f. NOTE: Dipped beam adjustment automatically causes dipped beam adjustment as well.

Sir, I was the one who wrote the subject, and now I saw it when I was on vacation and was looking for a cupra lip.

My foot is in plaster, but I'll try to disassemble it tomorrow.

I do not know if I thank you.

the subject is beautiful, the expression is great