206 Pulling Back Door Speaker Wiring - 206 - Peugeot Forum

You're welcome, I always try to help with this. A bit of trouble, I was wearing a Sony 1338f, there were no amps, but it was disrupting the sound, trying to give bass, but it wasn't enough.

Before starting work

2x0.22 cable up to 15mt
At least 4 iso female terminals
At least 8 male socket terminals

To insert the doors
Clip removal device
20 and 25 torx switches

Back up the door clip (circlip) service with 40 rt kurus number. If possible, take the tire type.

You can also enter insulation while inserting the doors. I made insulation and re-wiring to the doors on my own in 4 days.

There is no problem in removing the upholstery.I have a clip in my hand.I have removed the front doors without breaking any of the clips without damaging them. I cut the most acoustic sponge and put it on the floor before I install the floor.

[QUOTE = Acquisition] Hi,

Now there is a point that I don't understand. Let's be a natural one there.

The sockets on the tape in your vehicle should be as follows.

Here on the left is the socket for the speakers cable. The middle four ten speakers are on the right and the left bottom is the cable of the rear speakers. there must be 8 cables in total. Are there any missing?

If any, the process will be complicated.
[/ QUOTE]

hello my brother i have 2011 model 206+ too i have (http://urun.gittigidiyor.com/otomobil-motor-aksesuar/sony-dsx-a200-usb-oto-teyp-ile-fb131-13cm-fb161-16cm- speakerlor-set-275101555) link sony dsx a200 tape and front and rear speakers i got the wiring cable in the back doors, it was not possible to disassemble the old tape new tapes and speakers are possible to connect the new tape to the steering wheel in cargo, thanks in advance ... Başparmak havaya

we black_j 2017-06-11 22:26:33

[QUOTE = We black_j]

[/ QUOTE]

I will answer :)

I visited a few plumbers and looked at it, and finally I got everything on the internet.

the same parts cost around 2800 3000 TL in plumbers, I recovered 2000 tly by piece. I started mounting today. When I finish collecting the car, I will open the subject.

I have 2011 comfort 206+, and comfort 206+ does not have a back door installation, 2 outputs are opened in tapes, only two channels are output in the sockets behind the tape.

so there is no exit from the tape to the back door. the same shape is in the mirror adjusting spot, the small tweeter and the ratio are not in the cable. There is also a loud speaker inside the door. 16.5 cm hoppers that I bought did not fit, I will try to wear with the hoop tomorrow.

Steering wheel control is also possible, but the confirmation has a W / R input. either you will get the apparatus, or if it comes from it, there are diodes of different value, you make them yourself.

When my assembly work is done, I will start the first ten.

my only suggestion is don't really trust plumbers. Gather piece by piece from right to left from the internet, and if you can, assemble everything yourself.

For the original tape -> If you want speakers on the back doors, you will first open the tape's 4 channel output, and you will pull the tape from the tape to the back door. a little laborious. you will need to install a 20 25 rms speaker, which will also be removed by the original confirmation, which is how much quality sound it is worth or is it worth discussing.

08.05.2020 19:23	# 41
Samet Cetin
You're welcome, I always try to help with this. A bit of trouble, I was wearing a Sony 1338f, there were no amps, but it was disrupting the sound, trying to give bass, but it wasn't enough.

08.05.2020 19:23	# 42
Alicilik
Before starting work 2x0.22 cable up to 15mt At least 4 iso female terminals At least 8 male socket terminals To insert the doors Clip removal device 20 and 25 torx switches Back up the door clip (circlip) service with 40 rt kurus number. If possible, take the tire type. You can also enter insulation while inserting the doors. I made insulation and re-wiring to the doors on my own in 4 days.

08.05.2020 19:23	# 43
samet206
There is no problem in removing the upholstery.I have a clip in my hand.I have removed the front doors without breaking any of the clips without damaging them. I cut the most acoustic sponge and put it on the floor before I install the floor.

08.05.2020 19:23	# 44
black_jeruz
[QUOTE = Acquisition] Hi, Now there is a point that I don't understand. Let's be a natural one there. The sockets on the tape in your vehicle should be as follows. Here on the left is the socket for the speakers cable. The middle four ten speakers are on the right and the left bottom is the cable of the rear speakers. there must be 8 cables in total. Are there any missing? If any, the process will be complicated. [/ QUOTE] hello my brother i have 2011 model 206+ too i have (http://urun.gittigidiyor.com/otomobil-motor-aksesuar/sony-dsx-a200-usb-oto-teyp-ile-fb131-13cm-fb161-16cm- speakerlor-set-275101555) link sony dsx a200 tape and front and rear speakers i got the wiring cable in the back doors, it was not possible to disassemble the old tape new tapes and speakers are possible to connect the new tape to the steering wheel in cargo, thanks in advance ... we black_j 2017-06-11 22:26:33

08.05.2020 19:23	# 45
maximusti
[QUOTE = We black_j] hello my brother i have 2011 model 206+ too i have (http://urun.gittigidiyor.com/otomobil-motor-aksesuar/sony-dsx-a200-usb-oto-teyp-ile-fb131-13cm-fb161-16cm- speakerlor-set-275101555) link sony dsx a200 tape and front and rear speakers i got the wiring cable in the back doors, it was not possible to disassemble the old tape new tapes and speakers are possible to connect the new tape to the steering wheel in cargo, thanks in advance ... [/ QUOTE] I will answer :) I visited a few plumbers and looked at it, and finally I got everything on the internet. the same parts cost around 2800 3000 TL in plumbers, I recovered 2000 tly by piece. I started mounting today. When I finish collecting the car, I will open the subject. I have 2011 comfort 206+, and comfort 206+ does not have a back door installation, 2 outputs are opened in tapes, only two channels are output in the sockets behind the tape. so there is no exit from the tape to the back door. the same shape is in the mirror adjusting spot, the small tweeter and the ratio are not in the cable. There is also a loud speaker inside the door. 16.5 cm hoppers that I bought did not fit, I will try to wear with the hoop tomorrow. Steering wheel control is also possible, but the confirmation has a W / R input. either you will get the apparatus, or if it comes from it, there are diodes of different value, you make them yourself. When my assembly work is done, I will start the first ten. my only suggestion is don't really trust plumbers. Gather piece by piece from right to left from the internet, and if you can, assemble everything yourself. For the original tape -> If you want speakers on the back doors, you will first open the tape's 4 channel output, and you will pull the tape from the tape to the back door. a little laborious. you will need to install a 20 25 rms speaker, which will also be removed by the original confirmation, which is how much quality sound it is worth or is it worth discussing.

	206 Pulling Back Door Speaker Wiring
• Homepage » PEUGEOT MODIFIED PLATFORM » 206