206 PLUS 3-LINE SCREEN MOUNTING AID

MY FRIENDS IN MY HELL. FORM. MY VEHICLE 2010 206 PLUS COMFORT MODEL. MY FIRST CAR :) I HAVE ORDERED A 3-LINE SCREEN FOR MY VEHICLE.
1-HOW TO REMOVE THE CONSOLE AND HOW TO CONNECT THE ROAD COMPUTER?
2-HOW TO REMOVE THE KEY ON THE WIPER'S HANDLE? WHICH PART WILL I SPRING AND WHICH I BREAK?
3- IS THERE I NEED TO GO TO THE SERVICE AFTER INSTALLING THE ROAD COMPUTER TO OPEN ANYTHING? NO MOBILITY AT THE PRESS OF THE RDS KEY.

monalos 2015-02-03 13:06:36

I wrote a few times if you searched a little.

[QUOTE = monalos]
[/ QUOTE]

206+ same as 207 different from 206.

THE CONSOLE LIKES IT.

If I helped it look like 206, would you find it 207? Console but you will find it.

I HAVE SEARCHED AND WERE NOT FOUND.There are 206 SHARES ABOUT ANYWHERE IS NO PLUS TOOL.

[QUOTE = qimyager] CONSOLE LIKES THIS. I WOULD LIKE YOU HELP.
[/ QUOTE]

You did not read the rules while registering in the forum. It is wrong to write a capitalized letter in the foruns. I recommend that you pay attention to this first and correct your existing articles and open a title that introduces yourself.

Detailed documentation on the insertion of the 206-2 and 207 into the breast is a little bit of research.

First of all, I apologize for violating the forum rules. I could not find the detailed documents. I have been researching for how many days.

Nobody has 206 plus? Or for the first time I will plug it in the trip computer :)

I looked at it and wrote who will not disassemble it: D there is no subject at all on this site.

I am afraid that I will disassemble it, but it will be in my hand.

Try it slowly and understand it: D I did not know how it was dismantled. At 206, I moved the hat of the information screen a little bit, I shook, I thought I drew it in 1-2 minutes: D

can you take a photo of the console

I think I will wait and throw it: D

I'm waiting, brother :)

I attempted unknowingly, there is nothing to be afraid of.

1- The panel has a black frame. The air conditioner covers the top of the screen with its mouths. Begin to remove this frame from the top of the screen hat with a thin screwdriver. It has some nails. It may be a little difficult because it will be removed for the first time, but it is removed. You will go down from above.

2- After the frame, there are 2 pieces of 20 torx screws to remove them.

3- Grasp the finger on the right and left of the panel and pull it up and towards you. When it comes out, immediately remove the socket of the flasor.

4- There are 2 torx screws in the upper corners of the screen. unscrew them.

5- The cable of the screen is connected to the top of the screen with a socket and the cable is fixed with a bridge at the end of the screen. Free the cable from there.

6- Press down on the socket and lower the belt. The socket will come out.



The installation process is just the opposite. Do not forget the socket of the flasher.



For the key,

Remove the cap on the end of the wiper arm with a knife or a thin screwdriver.

there are feet under it, break them up tiny

remove a ballpoint pen. cut a little about 1 cm from the spring, slightly widen the tip and put it on the end of the place you removed.

Cut it from the back of the pencil to 2.5cm, put a thin hole there and close the lid.



that is all



According to the situation, there is a need for activation from the computer in the on-board computer. The trip computer parameter is not on the vehicle. The parameter is in the display brain. If the parameter on the screen is open, you will get the information. But you need to open it with parameter kappap on the screen.


For RDS, you need to change the location setting from the radio parameters from Asia to Eastern Europe.

Turn on the fader setting while entering the ready radius menu. Rear speakers are activated this way.

Thank you for the information you have provided, brother Ali.

No very detailed photos. It is not as difficult as you think.

When you remove the frame, the edges will look like this



Here are the torx screws I mentioned that will be screws in the holes below.




This is the top of the screen.



These are what I have to pay attention to the screws, especially the screws of the screen.

Thank you. I hope I will be successful :)