206+ cruise ideas with 207 cruise transactions ...

Hello; I searched my vehicle 206+ a lot, I did not come across cruise control, but I felt the need to open such a subject because our vehicle has 207 variants. and brain services> Electronic control unit testing> Intelligent distribution box (BSI)> Remote coding> Customer options> We follow the different path: "Change speed / no limitation" according to the cruise control we have installed: For remote coding after making our selections "F5 "We press the key: If we saw this screen, we completed the first part: Back to top Introduction and brain services> Test with the electronic control unit> Engine / Gearbox> Engine brain> Configuration> Remote coding path:" Vehicle cruise control "and the speed you installed I fix We change the "Vehicle speed limitation" values to "Available" if there is any: After making our selections, we press the "F5" key for remote coding: If we saw this screen, the process is ok:

206 1.4 Hdi was a speed stabilizer in my vehicle. brake customer must have 4 wires and clutch sender.

All infrastructure is ready in 206+ model but there is a software solution.

The blush tried very hard and tried all of these pictures and more, but unfortunately she couldn't work

I wonder how accurate it was when the setting was made from pp2000 in 206+, causing problems in the service.

I talked to Ali, the indicators are mixed, he explains himself when he sees the subject

[QUOTE = Serco05] Indicators are mixed. I spoke to Ali, I am self-explanatory. I woke up on Saturday at 9am and I am standing with a total of 7 hours of sleep so far.

We talked to my teacher who opened the message, but I don't know if we talked about this part.

In vehicles of 2008 and above, pp2000 is not used much. Instead, there is a more user-friendly interface called Diagbox. It is necessary to work from there.

206+ not only the bugs in BSi are not fixed. At least that's my problem.

If your vehicle is 206+ and complies with the table below



It's done smoothly. I will discuss the part of how it is being done before, under another topic, but it happens. Leave the ppp2000, we even tried 207 hogger, we tried all the tools from bottom to top left to right. Maybe it was not enough, maybe we went to CITROEN and tried all the vehicles there one by one. I don't know if there was this much dealing, because we worked for 3 days from 9 in the morning to 6 in the evening. Didn't we try the sender or access to the brain? what we didn't do was change the last BSi but it is very costly.

became an apan. The forum has SPEARO nicnki cenker brother. You yourself have it from our vehicle, and it's doing it consciously. He made it to a friend's car and it happened. The 4th gear opens at 70km and even looks like the original on the indicators.

He also had difficulties with the part and we are in constant contact with him. I guess he is not very interested in density these days.

Whatever we tried on my vehicle, BSi had to be clean in terms of error. My fuse was blown a few times and the chassis was also contactless. They have to be erased in their brain, but there is no master to do it. Since I bought a new vehicle (we bought auris, but I did not have cc :( ....), I dumped 206+ a bit. We also use it in everyday traffic in the city. as before.

No need to enter 207 with PP2000. The purpose of entering 207 is that some 206s do not have a menu to open a cruise. In the 207s and partners they make this menu open from there. But if you enter 206+, it is not useful to enter another vehicle that is already open to the menu. When you enter and open;

-When the vehicle resumes, all of the indicators light up and the stop text flashes. KM writings become line by line. In this way, the service personnel never leaves it and restores it. Because the Briis left this way, the cruise worked, but the BSi burned.
- When you cancel back, it goes back to its original state.

friends this process is not as difficult as it is thought.
diesel 206+ comfort was loaded with me. In the assembly loading guide of the arm coded xxxx.z8, the warnings in the arm and indicator have been activated without any extra operations being applied.

Diagbox must be used in the loading process. The bsi fireware over the 2008 model does not allow processing with the pp2000.

While installing diagbox, it checks the bsi and general hardware for fault. If there is an error with
registered and you do not delete it, it does not install any. bsi also had a recorded error due to short circuiting tape and trunk lamp, so it could not be installed.
with a simple fault removal process this is a problemable issue (must be the diagnosticist who knows)

206+ bsi sine we have loaded the cruise control I obtained the diagbox, connected and checked the parameters, and confirmed the information I had learned before.
The location of the vehicle in bsi changed asia instead of asia.

while fixing all the mysteries,

coded xxxx.z8 in psa stock as of 2013. cruise control arm disappeared, I am following to get the track;)

[QUOTE = spearo] friends, this process is not as difficult as you think.
diesel 206+ comfort is loaded with me. Alerts on the arm and indicator have been activated without any extra operation except the operations in the installation installation guide of the arm with the code xxxx.z8.
[/ QUOTE]

Brother, you are now summary

[QUOTE = spearo]
while resolving all mysteries, the cruise control arm coded xxxx.z8 in psa stock disappeared as of 2013, I'm following for the supply;)
[/ QUOTE]

Excuse me that I sold the piece, I regret it like a donkey. Brother was our part code .z8 also? I remember that they are old pieces.

Friends have a little to do with the subject, but: D & nbsp;

[QUOTE = serkan719] friends have a little to do with the subject, but: D & nbsp; [/ QUOTE]

[QUOTE = serkan719] friends have a little to do with the subject, but: D & nbsp;

I haven't tried it in 2004, but I will try again

http://www.peugeotmarket.com/hız-sabıtleme-kolu,pr-278.html

[QUOTE = jack67] I haven't tried it in 2004, but I will try again
[/ QUOTE]

İsmail,

Have you checked the clients? I did not look at him at the meeting.
Must have done by logging in from the partner 207 or partner. Or it may be necessary to add BSi asleep, as Serco05 serkan brother did. Where did you try?

I do not think my vehicle will have a registered error in zero bsi. I have to try this process as soon as possible .

But there is a problem tomorrow one day, when a mistake falls, will the cruise cause trouble?

we tried with rapids in the rapids, we changed the cables with the 4-wire ones, but we pulled the cable. But we couldn't activate it.

[QUOTE = rdvnburton] I do not think my vehicle will have a registered error in zero bsi, I have to try this process as soon as possible. QUOTE]

I have a master in Ankara, teacher, but let's not talk to the man. Their noses are not a mess, they are officially in the air.

In Ankara,

There is a newly opened Arkas auto. Authorized pejo service. There is the Abdullah master he mentioned in his word. I can give you phone etc. You leave the car in the Arkas car, the master is struggling, you cannot go to it. So you have to describe it and the master doesn't make this recipe. There is a Tekin master in Ankara Fatih. He also helps a lot, but often he runs a lot of work.
Ankara Göral also helps the master but as I said, the words are not explained to the masters.

The procedure to be done is very simple. Cenker told me the steps. There is already an installation guide on the internet, I can throw it in English. The master is going to do it.

If there is a cable and a diagbox, I will deal, but it does not.


[QUOTE = rdvnburton] but there is a problem tomorrow one day, when a mistake falls, will the cruise cause trouble? [/ QUOTE]


BSi knowing the part in the first stage required. For this reason, the part is added and activated by the matching process. When any part is added to the BSI, there is no BSID error to accept and run it.

There was a problem afterwards, not a problem, it is enough to install once. If only an update is made, the current update will be canceled as this feature will still be off. After updating, you will have to activate again.



[QUOTE = jack67] We tried with the Abdullah master on the rapids, we replaced the cable with the 4-wire. tried to make adjustments. But it didn't work
[/ QUOTE]

Did he try 207 and his partner? And when did you try them?