Peugeot Forums - Peugeot Fan Club

206 99 2004 models cycle km hour

Homepage » PEUGEOT MODELS (FAULTS AND SOLUTIONS) » 206
08.05.2020 17:25 # 1
abdullah1972
I made the 2000 xr 206 rpm km fault by myself

08.05.2020 17:25 # 2
_PunisheR_
If you explain in detail how you did, if you have a picture or share it, people who meet in the forum can benefit
08.05.2020 17:25 # 3
hLL
[QUOTE = _PunisheR_] If you explain how you do it in detail, if you share a picture or something, people in the forum may benefit [/ QUOTE]
Just like me, the speed indicator is broken, it is absurd to say that I did. It will be more beautiful and useful if you elaborate on how you do it with some photos.
08.05.2020 17:25 # 4
abdullah1972
Someone else had done and shared his pictures before. I removed the instrument panel by looking at them. The parts that run the km and the tachometer are the same. The tiny motor and 2 gears. They did not knowingly make it durable. The engine, which is broken as much as the needle tip holding one of the gear, does not transmit motion to the needle even if the engine is broken. I broke the quilt needle in the place of the piece and heated it with a lighter. It was stronger than the factory did. It is very difficult to disassemble the dashboard. The digital km indicator strip is breaking off, it is hard to come across and adheres. It requires mimetric workmanship.


08.05.2020 17:25 # 5
hLL
[QUOTE = abdullah1972] someone else had done and shared their pictures before, looking at them, I removed the instrument panel. The parts that run the km and the tachometer are the same. Tiny motor and 2 gears. As if they did not knowingly made it durable. The plastic part broken as much as the needle tip holding one of the gear It does not transmit motion to the needle. I replaced the broken piece by warming it with a lighter needle.

I want to do it too but I'm afraid to open it if I can't collect it again. How did you remove the legend. & Nbsp; "Sleepy"

08.05.2020 17:25 # 6
_PunisheR_
http://forum.peugeotturkey.com/forum_posts.asp?tıd=18203&pn=2&title=206-gsterge-sklmesi-ark-tamiri-ve-led-uyg

There is a detailed topic here you can benefit
08.05.2020 17:25 # 7
hLL
[QUOTE = _punisher_] http://forum.peugeotturkey.com/forum_posts.asp?tıd=18203&pn=2&title=206-gsterge-sklmesi-ark-tamiri-ve-led-uyg

the subject is in detail here you can benefit

[/ QUOTE]

I know this, but there are no photos when removing it. Where do I apply force? I did not dare

08.05.2020 17:25 # 8
abdullah1972
It pulls the scratches on the outer panel of the dashboard towards the steering wheel. When it comes out, there is a screw on the top. It has two sockets on the back of the panel. and be careful with your ribbon or you will break it.
08.05.2020 17:25 # 9
abdullah1972
all nails can be removed by pressing with a flat screwdriver.

08.05.2020 17:25 # 10
hLL
OK, I will consider what you say. I'll take it off if I dare tomorrow. If I can, I will share lots of photos. Good evening.
08.05.2020 17:25 # 11
abdullah1972
the http://forum.peugeotturkey.com/forum_posts.asp?tıd=18203&pn=2&title=206-gsterge-sklmesi-ark-tamir
08.05.2020 17:25 # 12
_PunisheR_
it is not worth going to give 70-80 lira for what we can practice your hand cowardly
08.05.2020 17:25 # 13
hLL

[QUOTE = _PunisheR_] is not worth going to pay 70-80 lira for what we can practice his cowardly [/ QUOTE]

hobaa I have this gas yaaaaa & nbsp; "LOL" "LOL" nothing I can't do

08.05.2020 17:25 # 14
abdullah1972
will do it properly
Even if the master does not exist, he wants 200 300 TL.
08.05.2020 17:25 # 15
_PunisheR_
[QUOTE = hLL]

[QUOTE = _PunisheR_] is not worth it to go 70-80 lira for what we can practice cowardly [/ QUOTE]

hobaa I have this gas yaaaaa & nbsp; There is nothing I can not do

[/ QUOTE] do it, brother, do not hesitate to waste your money, your hand skill increases "LOL"
08.05.2020 17:25 # 16
abdullah1972
If the masters want the new piece, I would wear it myself.
Peugeot Forums - Peugeot Fan Club © 2024
“The most auspicious of people, it is people who are useful.”