|
|
|
|
205 * 55 * 16 Wheel tire did not fit 306 ?? URGENT! |
| • Homepage » PEUGEOT MODIFIED PLATFORM » Peugeot Wheel Tire Selection | |
| 08.05.2020 14:18 | # 1 |
 erhant2005 |
|
|
In recent months, I bought a second-hand Alessio 16 '' rim. According to the rim, I bought a second hand but very clean Pirelli Pzero Nero 205 * 55 * 16 tire. But because of my work, I could not get it installed in the car, it was lying at home, both wheels and tires. Yesterday I went to have my familiar tire tire, I already knew that the flange would be put together because the rim was wide. When we put the flange and put the rim on the car, the tires rub against the front and rear fenders. How can we take care of this? Are there any people who wear 205 * 55 * 16 tires on their 306? If we raise the torsion a couple of teeth, will the problem be solved? I am waiting for your comments and suggestions on this subject ... Good forums to everyone.
|
|
| 08.05.2020 14:18 | # 2 |
 Guests |
|
|
we had 205-55-17 rims in our 306 and maxtrax had a 5 cm spring.
|
|
| 08.05.2020 14:18 | # 3 |
| Guests |
|
|
First, a 205/55/16 tire is a very large tire for 306 tires. this tire is used in the 307s, for example. but it is about 6% bigger than the original tire of your vehicle. buddha is not recommended. the original tire of your vehicle is either 185/65/14 turns or gti 195/55/15. These two sizes are 14 "and 15" rim sizes, which correspond exactly to each other. You can see this verification in the tire rim calculation section on www.lastik24.com . if you want to attach 16 to your vehicle. The tire you can use should be 195/50/16. Maybe it can be used in 205/50/16. but if you get up to 55 cheeks it is not suitable for the tire. There are 306s with 205/40/17 tires that I have seen in 17 ". Did you look at the offset while buying this wheel alone? What is the offset of the rim you bought? the offset value is the value that determines whether the rim should be inside or outside. Personally, I don't like the flans application because you have to change the spark plugs. you wear longer bujins etc. There is a risk of flaws in flans etc. I prefer that the rim is pressed directly with the hub ... @EMRAH = 205/55/17, I do not give much chance that the tire will go without a 306 da poking. I suppose you mean 45/17? |
|
| 08.05.2020 14:18 | # 4 |
| Guests |
|
|
it might be 45 right .. but with 17 rims there wasn't any kite, so I wanna overtake it
|
|
| 08.05.2020 14:18 | # 5 |
| Guests |
|
|
I usually see 205 40 17 for those wearing 17 "wheels ... |
|
| 08.05.2020 14:18 | # 6 |
 HakanGokdemir |
|
|
[QUOTE = cecol of] I usually see 205 40 17 for those wearing 17 "wheels ... [/ QUOTE] I agree with Cem, and I am absolutely against the flange thing. Choose that method, thinking well, buddy.
|
|
| 08.05.2020 14:18 | # 7 |
| erhant2005 |
|
|
friends, I'm confused nowadays, I made a mistake when entering a value. My tires are 205 * 50 * 16, but I mentioned it as 55 in my first message. Actually it will be 205 * 50 * 16 ... [QUOTE = cecol of] First, a 205/55/16 tire is a very large tire for 306 tires. this tire is used in the 307s, for example. but it is about 6% bigger than the original tire of your vehicle. buddha is not recommended. the original tire of your vehicle is either 185/65/14 turns or gti 195/55/15. These two sizes are 14 "and 15" rim sizes, which correspond exactly to each other. You can see this verification in the tire rim calculation section on www.lastik24.com . if you want to attach 16 to your vehicle. The tire you can use should be 195/50/16. Maybe it can be used in 205/50/16. but if you get up to 55 cheeks it is not suitable for the tire. There are 306s with 205/40/17 tires that I have seen in 17 ". Did you look at the offset while buying this wheel alone? What is the offset of the rim you bought? the offset value is the value that determines whether the rim should be inside or outside. Personally, I don't like the flans application because you have to change the spark plugs. you wear longer bujins etc. There is a risk of flaws in flans etc. I prefer that the rim is pressed directly with the hub ... @EMRAH = 205/55/17, I do not give much chance that the tire will go without a 306 da poking. I suppose you mean 45/17? [/ QUOTE] I have never looked at offset values. You say 195 * 50 * 16, but now if I buy this, will I have to apply the flange again if I attach it to the vehicle? So will it rub against the tire? (I guess you call it rubbing torsion) 195 * 50 * 16 is a measurement that I can fit on my vehicle without any flanges without any flanges? Thank you for your answers.
|
|
| 08.05.2020 14:18 | # 8 |
| Guests |
|
|
Look, I'm missing something I told you. Let me tell you again. the incident does not end in a direct tire. very important on the offset of the rim. If you put the tire on 1 rim, it will not surt, you can put it on another rim. I told you about that pain offset value. the phenomenon of standing inside or outside the rim. Also, if possible, use 195 50 16 and I think it will be better. Because it is a perfect match, I recommend it to you. can you peel offset and width of the rim you bought ??? Here is the offset of the original rim of the vehicle? writes on the left door ... I know how bad you will be in summer  |
|
| 08.05.2020 14:18 | # 9 |
| erhant2005 |
|
|
I understand but unfortunately I don't know the offset values ... I will also look at the original dimensions of the vehicle and write it down. So where can we learn the offset values of the rim I bought? Don't you write on it?
|
|
| 08.05.2020 14:18 | # 10 |
| erhant2005 |
|
|
I convey exactly what is written at the door: 185/65 R14 86T Roues 5,50 J14 4-24 Continental ..- contrast 2.4 2.4 Michelin MXT Energy Pirelli P3000 what should we understand from these values now? "" "" "" "" "" "" "" "" "" "" "" "" "" "" "" "" "" "" "" "" "" "" "" "" "" "" "" " I add this message to avoid flooding again ... values I found from a foreign site:
15 "
16 "
|
|
| 08.05.2020 14:18 | # 11 |
| erhant2005 |
|
|
this is the original picture of my rim on their site: it is referred to as "Alessio F1".
these are pictures of my rims (AlessioF1) I took:
I put the pictures here by reducing them to fit the page, a little fat etc .. Those who want to get out can look here: http://rctutku.com/306resim/01.jpg http://rctutku.com/306resim/02.jpg |
|
| 08.05.2020 14:18 | # 12 |
| Guests |
|
|
now look... 185/65 R14 86T ===== (It is the measurement of the tire of the vehicle's fabrication. Apparently the vehicle is 1.6) Roues 5,50 J14 4-24 ===== (5.50 is the width of the rim as it says, j14 is the 14 "rim, 4 is 4 bolts and 24 is offset. Continental ..- contrast 2,4 2,4 ===== (this shows the pressure you need to squeeze the tires) If it is necessary to come to the point, it is the same as I thought. You have bought yourself a wrong rim due to a little lack of information because you call offset 42. the offset of our bızım vehicle is not suitable for your vehicle of the wheels. If it is not suitable, the tire maker offered you a chance. I am telling you again, I do not recommend the heat of flux. I think you should sell the rims you bought and buy a rim with 20-24 offset plus not more than 7 "in width ...
|
|
| 08.05.2020 14:18 | # 13 |
| erhant2005 |
|
|
I understand that the reason my rim is not on my vehicle right now is because its offset is big. I have seen this wheel in another 306, even the owner of the vehicle has an advertisement. In fact, my current 16 "and 17 in that vehicle we looked at. That's why I said to him that if it happens to me, it is the same in my car, so he warns me ... so I decided to buy this wheel and I bought it ... So the conclusion from this correspondence right now is: whatever tire I put on the rim, I have to use a flange to install the rim on the vehicle ??
|
|
| 08.05.2020 14:18 | # 14 |
| Guests |
|
|
what a shame ... When you put a flange between the rim and the hub, it fits for the inside of the rim. For example, if you put a 2cm flange offset of the rim would be reduced from 42 to 22 |
|
| 08.05.2020 14:18 | # 15 |
| erhant2005 |
|
|
I understand, many thanks for the information you provided ... I put my wheel on sale then with the tire;)
|
|
| 08.05.2020 14:18 | # 16 |
| erhant2005 |
|
|
friends, I just met a friend who has put the alessio f1 rim for sale on sahibinden.com, but the room used the pejo 306 rims, but neither flanged nor anything else ... our rims are the same but do not fit my 2000 model 306? Are there any people who can come up with an idea?
|
|
