|
|
|
|
2004 307 xt horn does not work |
| • Homepage » PEUGEOT MODELS (FAULTS AND SOLUTIONS) » 307 | |
| 08.05.2020 18:28 | # 1 |
 mehmethannn |
|
|
I do not know if I need to introduce myself in opening each subject, but let me introduce briefly. My name is Mehmet, I am 33 years old and work at the bank. I reside in a district of Sivas. It's been about 3 weeks since I bought my car. when I received the horn and parking sensor were not working. The car is original at 34000 km. I showed it to a master yesterday. parking sensor reversing lamp was not working changed the client and the problem is solved. but I can't say the same for the horn. the master checked the electrical parts, but the problem is not from him. He said that if the steering box should open inside, it would take a long time to collect (the car should stay for 2 days), if it could not be repaired, the box there should be completely changed and the amount was about 550 TL. was the master of the master peuegot service. he left about 6 months ago and he opened a place. I am in a district and I travel about 150 km to get this done. could write friends with knowledge on this subject. Thank you very much in advance.
|
|
| 08.05.2020 18:28 | # 2 |
 tolga.onal |
|
|
The insurance may have blown The horn may be broken Cables inside steering wheel may have oxidized Com2000 winding your master says and this is the worst possibility. Everything can be done, a detailed check must be done.
|
|
| 08.05.2020 18:28 | # 3 |
| mehmethannn |
|
|
[QUOTE = tolga.onal] Could have blown insurance The horn may be broken Cables inside steering wheel may have oxidized Com2000 winding your master says and this is the worst possibility. Everything can be done, a detailed check must be done. [/ QUOTE] There is no problem in fuses tolga bey. Like com2000 wrap, something said to the master. I do not understand much from the car. He said it was a bit burdensome to collect, so the car must stay for 2 days, the master said. I wanted to consult you. Thank you for your answer.
|
|
| 08.05.2020 18:28 | # 4 |
 206cc57 |
|
|
I have com2000 malfunction in my vehicle. I turn on the fog, turn off by itself. If I turn on the park, my horn works, if I give a signal, the automatic lighting is disabled, when the signal goes off, it turns on again. I keep it open, the original of this piece is malasef expensive, it has a very affordable price on ebay, but I couldn't get it .. It doesn't make every place in the repair ..
|
|
| 08.05.2020 18:28 | # 5 |
| mehmethannn |
|
|
[QUOTE = 206cc57] My car has com2000 malfunction. I turn on the mists, turn off the fog. If I turn on the park, my horn works, if I give a signal, the automatic lighting is disabled, when the signal goes off, it turns on again. When I turn on the most beautiful headlights, everything works properly. I keep it open, the original of this piece is malasef expensive, it has a very affordable price on ebay, but I couldn't get it .. It doesn't do every place in repair .. [/ QUOTE] thank you mate for the information. The horn has been playing intermittently for two days :) I think he did something like oxidation because I got the electrical parts checked. Now let me put on a horn and drive it :)
|
|
| 08.05.2020 18:28 | # 6 |
 muhoist |
|
|
Remove the steering wheel hub You can disassemble it yourself. Sand the parts on the hub with the horn mark. Correct. This process takes a total of 5 minutes.
|
|
| 08.05.2020 18:28 | # 7 |
| mehmethannn |
|
|
[QUOTE = muhoist] Remove the hub of the steering wheel You can disassemble it yourself Sand the parts with the horn mark on the hub. It takes a total of 5 minutes. [/ QUOTE] I was unable to remove it because I was afraid of damaging it when disassembling. The place I am in is the district. If there is a malfunction I can not. so I did not disassemble it. the electrician has an uncle son made an original horn :) he immediately installed a very beautiful button next to the wiper and attached it to a new horn. i'm running for now
|
|
| 08.05.2020 18:28 | # 8 |
 65serdal58 |
|
|
Mehmet Bey also had a horn problem. The steering wheel was removed. The oxidized ends were cleared.
|
|
| 08.05.2020 18:28 | # 9 |
| mehmethannn |
|
|
[QUOTE = 65serdal58] mehmet bey also had a horn problem in me. Steering wheel was dismantled. Oxidized ends were cleared. And process is ok:) [/ QUOTE] Actually, I dismantle it based on the information in the forums, but as I said, I am in a district, if there is a problem, there is nobody to make or look, I have to go 130 km :) com If I damage 2000 bandage or something, this time it will cost 600-700 TL so I'm afraid ... :)
|
|
| 08.05.2020 18:28 | # 10 |
| Serkan |
|
|
Teacher, it is very easy to disassemble the steering hub, there is a situation where you have trouble, there is a hole under the steering wheel, there is a thick wire going through it, insert the screwdriver from that hole, press the wire strongly, if not, after screwing the screwdriver on the wire, hit the screwdriver firmly from the bottom, get rid of the fingernails and click on the screwdriver. she will throw.
|
|
| 08.05.2020 18:28 | # 11 |
| mehmethannn |
|
|
[QUOTE = Serkan] My teacher, it is very easy to remove the steering hub, there is a little bit of trouble for you, there is a hole under the steering wheel, there is a thick wire passing through it, insert the screwdriver from that hole, press the screw strongly, if not, then hit the screwdriver firmly from the bottom. the belly will get rid of the nails and click it. [/ QUOTE] ok serkan bey,
I'll try it as soon as possible but first I have to wear your horn. Uncle son made a new horn to the car and made a knob next to the wiper from other connections. like the horn in the old taurus :) We had to remove the old horn and did not wear a new one because it was bad. Let me get my horn attached. then I'll try to disassemble it as you say. Thank you very much for the information you provide. |
|
| 08.05.2020 18:28 | # 12 |
| Serkan |
|
|
You are welcome hodja, this painting makes your job easier, all you have to do is press it hard on the wire and it comes easy. 
|
|
| 08.05.2020 18:28 | # 13 |
| mehmethannn |
|
|
[QUOTE = Serkan] Thank you hodja, this painting makes your job easier, all you have to do is press it firmly and it comes easy. [/ QUOTE] I can't see the pictures here. I will look from home in the evening. Thank you again for everything. Thankfully there are helpful friends like you. well this forum exists :)
|
|