![]() ![]() |
|
![]() |
2002 MODEL 1.6 307XT HEATER PROBLEM |
• Homepage » PEUGEOT MODELS (FAULTS AND SOLUTIONS) » 307 |
08.05.2020 14:13 | # 1 |
![]() |
|
I HAVE USED 3 YEARS 2002 MODEL 1.6 307XT THERE IS NO MISSION, THERE WAS MACHINE BUT IT IS SO MUCH TO BE HEALLY HAPPEN AS I LIKE THE SOUTH OF THE LIGHT LEVEL OF THE LIGHT STAGE WHEN THE HEATER HAS BEEN OPENED IN ANY STAGE, AND I WOULD LIKE TO HALF THAT THE HIGH FAN SOUND. WHAT IS THE PROBLEM IF YOU HAVE A KNOWLEDGE, COME BEFORE :))
|
08.05.2020 14:13 | # 2 |
![]() |
|
Could the screws of the heater motor (fan) be loose?
|
08.05.2020 14:13 | # 3 |
![]() |
|
the balance of the heating engine may be broken or there may be a small fracture in the propeller .. I have the same problem.
|
08.05.2020 14:13 | # 4 |
![]() |
|
brother, how do I disassemble it? They say that the front panel must be completely removed, and they do not advise in removing the front panel. What should I do?
|
08.05.2020 14:13 | # 5 |
![]() |
|
I do not know what it is but describe it to me that I can do it, I have manual skills, I can detach things, but I cannot do without the service without removing the front panel.
|
08.05.2020 14:13 | # 6 |
![]() |
|
I know the location of the heater core, but I do not know where the engine is. I have no idea how to disassemble it. Maybe Haşim Usta will help in this regard, if you have an illustrated narration ..
|
08.05.2020 14:13 | # 7 |
![]() |
|
First of all, I want to peel the presentation. Also, I think you should not try to do what you do and how to do it before you do not see such a heat before. you can damage other parts. I am a human being mechanically like you. But torpedo is not a heat. Check under the passenger side thoroughly, maybe you may be able to reach a fan. I usually say because it is in that area. Of course, my friends who are more knowledgeable than me about their 307 torpedo will help you. I must not forget why I do not advise why the torpedo is inserted because disturbing noises can start to creak after the torpedo is inserted and installed ... |
08.05.2020 14:13 | # 8 |
![]() |
|
Unfortunately, there are no photographs, but let me explain ... remove the felt on the pedals by removing the pins first.Remove the cover under the steering column from above to the bottom, then unscrew the screws in the foot ventilation hole of the center console and remove that wide side part. If you follow the black red cables, you will reach the heating engine (there is only one bright screw, it looks when you lean on the engine and see it). be careful not to get caught in the harness when removing it from the ground, also it is useful to stretch the console while passing it near the gas pedal because its propeller looks very sensitive. But if you ask me, a piece of dry leaf that escapes inside or something similar may be the reason for this, if the propeller balance or the engine has a problem, the noise will increase as the cycle increases. dismantling and propeller risk of breaking ... |
08.05.2020 14:13 | # 9 |
![]() |
|
master, do not dismantle the front console, I had the 307 xt accelerator pedal changed from there, did not remove the chest or something, hakan master immediately took 1.5 hours.
|
08.05.2020 14:13 | # 10 |
![]() |
|
If you can't reach the gas pedal from there, just unscrew the torpedo and you can easily reach it from there .... |
08.05.2020 14:13 | # 11 |
![]() |
|
IF FRIENDS WILL HELP ME ON THIS TOPIC, YOU CAN RECOMMEND A MASTER IN ISTANBUL. I LOVE MY CAR VERY AND I DO NOT WANT TO PROBLEM. CAN YOU CHOOSE A NAME AND SURNAME NUMBER
|